AD9100JD Analog Devices Inc, AD9100JD Datasheet - Page 3

• Manufacturer Part Number: AD9100JD
• Manufacturer: Analog Devices Inc

Specifications of AD9100JD

• Number Of Sample And Hold Elements: 1
• Power Supply Requirement: Dual
• Single Supply Voltage (typ): Not RequiredV
• Single Supply Voltage (min): Not RequiredV
• Single Supply Voltage (max): Not RequiredV
• Operating Temperature Classification: Commercial
• Mounting: Through Hole
• Lead Free Status / RoHS Status: Not Compliant

EXPLANATION OF TEST LEVELS
Test Level
I
II – 100% production tested at +25 C, and sample tested at
III – Periodically sample tested.
IV – Parameter is guaranteed by design and characterization
V – Parameter is a typical value only.
VI – All devices are 100% production tested at +25 C. 100%
REV. A
Parameter
HOLD-TO-TRACK SWITCHING
POWER SUPPLY
NOTES
Specifications subject to change without notice
1
2
3
4
5
6
Absolute maximum ratings are limiting values to be applied individually, and beyond which the serviceability of the circuit may be impaired. Functional operability
is not necessarily implied. Exposure to absolute maximum rating conditions for an extended period of time may affect device reliability.
Analog input voltage should not exceed V
AD9100JD: 0 C to +70 C. AD9100AD: –40 C to +85 C. AD9100SD: –55 C to +125 C. DIP
grounded 2 oz copper clad board with 16 sq inches of surface area and no air flow. LCC
The input to the AD9100 is internally clamped at 2.3 V. The internal input series resistance is nominally 50
Hold mode noise is proportional to the length of time a signal is held. For example, if the hold time (t
20 ns). This value must be combined with the track mode noise to obtain total noise.
Min and max droop rates are based on the military temperature range (–55 C to +125 C). Refer to the “Droop Rate vs Temperature” chart for min/max limits over
the commercial and industrial ranges.
Acquisition Time to 0.1%
Acquisition Time to 0.01%
Acquisition Time to 0.01%
Power Dissipation
+V
–V
– 100% production tested.
S
S
specified temperatures.
testing.
production tested at temperature extremes for extended
temperature devices; sample tested at temperature
extremes for commercial/industrial devices.
Current
Current
HOLD CAPACITOR/
ANALOG OUTPUT
ANALOG
INPUTS
CLOCK
INPUT
–2V
+2V
–2V
S
+2V
"1"
"0"
.
0V
0V
CLOCK (PIN #19)
"HOLD"
Conditions
2 V Step
2 V Step
4 V Step
AD9100 Timing Diagram (1 ns/div)
SWITCH
TRACK
DELAY
HOLD
TIME
(4ns)
TO
ACQUISITION TIME
(16ns)
–3–
Model
AD9100JD
AD9100AD
AD9100AE
AD9100SD
AD9100SE
NOTE
l
Consult factory about availability of parts screened to MIL-STD-883.
"TRACK"
CLOCK
Temp
25 C
Full
25 C
Full
Full
Full
ANALOG OUTPUT
HOLD CAPACITOR
JA
OBSERVED AT
OBSERVED AT
= 48 C/W.
1
JA
= 38 C/W; this is valid with the device mounted flush to a
H
) is 20 ns, the accumulated noise is typically 6 V (300 V/s
Test
Level
V
IV
V
VI
VI
VI
–55 C to +125 C
0 C to +70 C
–40 C to +85 C
–40 C to +85 C
–55 C to +125 C
Temperature
Range
ORDERING GUIDE
.
AD9100AE/SE/JD/AD/SD
Min
APERTURE
VOLTAGE
DELAY
(0.8ns)
TRACK TO
SETTLING
LEVEL
HELD
HOLD
(7ns)
"HOLD"
Typ
13
16
20
1.05
96
116
Package
Description
Ceramic DIP
Ceramic DIP
Ceramic LCC E-28A
Ceramic DIP
Ceramic LCC E-28A
Max
23
1.25
118
132
AD9100
3
Package
Option
D-28
D-28
D-28
ns
Units
ns
ns
W
mA
mA