MCP2200T-I/MQ Microchip Technology, MCP2200T-I/MQ Datasheet - Page 11

• Manufacturer Part Number: MCP2200T-I/MQ
• Description: USB 2.0 To UART Protocol Converter With GPIO 20 QFN 5x5x0.9mm T/R
• Manufacturer: Microchip Technology

Specifications of MCP2200T-I/MQ

• Features: USB to UART
• Number Of Channels: 8
• Fifo's: 256 Byte
• Protocol: USB 2.0
• Voltage - Supply: 3 V ~ 5.5 V
• With Auto Flow Control: Yes
• Mounting Type: Surface Mount
• Package / Case: 20-VQFN Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

2.0
2.1
V
V
V
V
V
V
V
V
V
V
I
ESD protection on LIN, V
ESD protection on LIN, V
ESD protection on all other pins (Human Body Model) (Note 5) ............................................................................ ±4 KV
ESD protection on all pins (Charge Device Model) (Note 6) .................................................................................. ±2 KV
ESD protection on all pins (Machine Model) (Note 7).............................................................................................±200V
Maximum Junction Temperature ............................................................................................................................. 150C
Storage Temperature .................................................................................................................................. -65 to +150C
2.2
Some terms and names used in this data sheet deviate from those referred to in the LIN specifications. Equivalant
values are shown below.
 2010 Microchip Technology Inc.
LBUS
† NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
IN
IN
BB
BB
BB
BB
BB
BB
LBUS
LBUS
Note 1: LIN 2.x compliant specification.
DC Voltage on R
DC Voltage on CS, WAKE and V
Battery Voltage, continuous, non-operating (Note 1)..............................................................................-0.3 to +40V
Battery Voltage, non-operating (LIN bus recessive) (Note 2) .................................................................-0.3 to +43V
Battery Voltage, transient ISO 7637 Test 1 ......................................................................................................-200V
Battery Voltage, transient ISO 7637 Test 2a ...................................................................................................+150V
Battery Voltage, transient ISO 7637 Test 3a ....................................................................................................-300V
Battery Voltage, transient ISO 7637 Test 3b ...................................................................................................+200V
Bus Short Circuit Current Limit ....................................................................................................................200 mA
Bus Voltage, continuous.......................................................................................................................-18 to +30V
Bus Voltage, transient (Note 3)............................................................................................................-27 to +43V
2: SAE J2602 compliant specification.
3: ISO 7637/1 load dump compliant (t < 500 ms).
4: According to IEC 61000-4-2, 330 ohm, 150 pF and Tranceiver EMC Test Specifications [2] to [4]. For WAKE
5: According to AEC-Q100-002 / JESD22-A114.
6: According to AEC-Q100-011B.
7: According to AEC-Q100-003 / JESD22-A115.
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings†
Nomenclature used in this document
LIN 2.1 Name
pin to meet the specification, series resistor must be in place (refer to
V
V
I
BUS
BUSDOM
V
V
BUSREC
BAT
SUP
_
LIM
XD
, T
BB
BB
XD
, WAKE (IEC 61000-4-2) (Note 4) .............................................................................. ±8 KV
(Human Body Model) (Note 5)................................................................................... ±8 KV
, FAULT/TXE .....................................................................................................-0.3 to +30V
REN
Term used in the following tables
.......................................................................................................-0.3 to +30V
V
V
not used
IH
IL
V
(L
(L
I
SC
BB
BUS
BUS
)
)
Example
Supply voltage at device pin
ECU operating voltage
Current Limit of Driver
MCP2003/4
Recessive state
Dominant state
1-2).
Definition
DS22230C-page 11