SI3202-G-FSR Silicon Laboratories Inc, SI3202-G-FSR Datasheet - Page 42
![no-image](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_sml.jpg)
SI3202-G-FSR
Manufacturer Part Number
SI3202-G-FSR
Description
Manufacturer
Silicon Laboratories Inc
Datasheet
1.SI3202-G-FSR.pdf
(112 pages)
Specifications of SI3202-G-FSR
Lead Free Status / RoHS Status
Compliant
Si3220/25 Si3200/02
3.9. Automatic Dual Battery Switching
The Dual ProSLIC chipsets provide the ability to switch
between several user-provided battery supplies to aid
thermal management. Two specific scenarios where
this method may be required follow:
The BATSELa and BATSELb pins switch between the
two battery voltages based on the operating state and
the TIP-RING voltage. Figure 19 illustrates the chip
connections required to implement an automatic dual
battery switching scheme. When BATSEL is pulled
LOW, the desired channel is powered from the V
supply. When BATSEL is pulled HIGH, the V
supplies power to the desired channel.
42
Ringing to off-hook state transition (Si3220):
During the on-hook operating state, the Dual
ProSLIC chipset must operate from the ringing
battery supply to provide the desired ringing signal
when required. Once an off-hook condition is
detected, the Dual ProSLIC chipset must transition
to the lower battery supply (typically –24 V) to
reduce power dissipation during the active state. The
low current consumed by the Dual ProSLIC chipset
during the on-hook state results in very little power
dissipation while being powered from the ringing
battery supply, which can have an amplitude as high
as –100 V depending on the desired ringing
amplitude.
On-hook to off-hook state, short loop feed
(Si3225): When sourcing both long and short loop
lengths, the Dual ProSLIC chipset can automatically
switch from the typical –48 V off-hook battery supply
to a lower off-hook battery supply (e.g., –24 V) to
reduce the total off-hook power dissipation. The Dual
ProSLIC chipset continuously monitors the TIP-
RING voltage and selects the lowest battery voltage
required to power the loop when transitioning from
the on-hook to the off-hook state, thus assuring the
lowest power dissipation.
BHI
source
BLO
Rev. 1.3
The BATSEL pins for both channels are controlled using
the BATSEL bit of the RLYCON register and can be
programmed to automatically switch to the lower battery
supply (V
low enough to allow proper operation from the lower
supply. When using the Si3220, this mode should
always be enabled to allow seamless switching
between the ringing and off-hook states. The same
switching scheme is used with the Si3225 to reduce
power by switching to a lower off-hook battery when
sourcing a short loop.
Automatic battery selection should be disabled before
using the manual battery select control bit (BSEL bit,
Register 5—RLYCON,
Laboratories for information on how to disable
automatic battery selection.
Two thresholds are provided to enable battery switching
with hysteresis. The BATHTH RAM location specifies
the threshold at which the Dual ProSLIC device
switches from the low battery (V
(V
BATLTH RAM location specifies the threshold at which
the Si3220/Si3225 switches from V
transition from the on-hook or ringing state to the off-
hook state or because the overhead during active Off-
Hook mode is sufficient to feed the subscriber loop
using a lower battery voltage.
The low-pass filter coefficient is calculated using the
following equation and is entered into the BATLPF RAM
location:
BATLPF = [(2 π f x 4096)/800] x 2
Where f = the desired cutoff frequency of the filter
The programmable range of the filter is from 0h (blocks
all signals) to 4000h (unfiltered). A typical value of
10 Hz (0A10h) is sufficient to filter out any unwanted ac
artifacts while allowing the dc information to pass
through the filter.
Table 23 provides the register and RAM locations used
for programming the battery switching functions.
BHI
) due to an off-hook-to-on-hook transition. The
BLO
) when the off-hook TIP-RING voltage is
bit 5).
3
BLO
BHI
) to the high battery
Contact
to V
BLO
due to a
Silicon