LULXT9785MBC.D0-865133 Cortina Systems Inc, LULXT9785MBC.D0-865133 Datasheet - Page 164
LULXT9785MBC.D0-865133
Manufacturer Part Number
LULXT9785MBC.D0-865133
Description
Manufacturer
Cortina Systems Inc
Datasheet
1.LULXT9785MBC.D0-865133.pdf
(221 pages)
Specifications of LULXT9785MBC.D0-865133
Lead Free Status / RoHS Status
Compliant
- Current page: 164 of 221
- Download datasheet (4Mb)
LXT9785/LXT9785E
Datasheet
249241, Revision 11.0
16 April 2007
5.2.6
Figure 33
Cortina Systems
Refer to the fiber transceiver manufacturer’s recommendations for termination circuitry.
Figure 36
interface.
The following occurs in 5 V fiber transceiver applications as shown in
Refer to the fiber transceiver manufacturer’s recommendations for termination circuitry.
Figure 37
interface, while
LED Circuit
Each Direct Drive LED has a corresponding open-drain pin. The LEDs are connected
through a current-limiting resistor to a positive-voltage rail. The LEDs are turned on when
the output pin drives Low. The open-drain LED pins are 5 V tolerant, allowing use of either
a 3.3 V or 5 V rail (a 2.5 V rail is unlikely to work with standard forward voltage LEDs). A 5
V rail eases LED component selection by allowing more common, high-forward voltage
LEDs to be used. Refer to
LED Circuit
®
• The receive pair should be DC-coupled with an emitter current path for the fiber
• The signal detect pin should be DC-coupled with an emitter current path for the fiber
• The transmit pair should be AC-coupled and re-biased to 5 V PECL input levels
• The transmit pair should contain a balance offset in the pull-up resistors to prevent
• The receive pair should be AC-coupled with an emitter current path for the fiber
• The signal detect pin on a 5 V fiber transceiver interface should use the logic
LXT9785 and LXT9785E Advanced 8-Port 10/100 Mbps PHY Transceivers
transceiver
transceiver
PHY-to-fiber transceiver crosstalk amplification in power-down, loopback, and reset
states (see fiber interface application note)
transceiver and re-biased to 1.2 V
translator circuitry as shown in
shows a typical example of an LXT9785/LXT9785E-to-3.3 V fiber transceiver
shows a typical example of an LXT9785/LXT9785E-to-5 V fiber transceiver
Figure 38
shows the interface circuitry for the logic translator.
Figure 33
VCCIO < V
Figure
for a circuit illustration.
Inside
IC
38.
LED
LED n _m
Outside
R
IC
V
< 5 V + 5%
LED
5.2 General Design Guidelines
Figure
37:
Page 164
Related parts for LULXT9785MBC.D0-865133
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
IC ETH MAC SPI3 4-PORT 552-FCBGA
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
IC ETH MAC SPI3 4PORT 552-BGA
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
IC ETHERNET MAC 10PORT 552-CBGA
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
IC ETHERNET MAC 10-PORT 552-BGA
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
IC ETH MAC 12-PORT 1152-UPBGA
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
IC ETH MAC 24-PORT COMM 672-BGA
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
IC ETH MAC 24-PORT 1152-UPBGA
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
IC ETH AGGREGATOR 4P 1024-BGA
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
IC ETH AGGREGATOR 4PORT 1024-BGA
Manufacturer:
Cortina Systems Inc
Datasheet:
Part Number:
Description:
IC ETH AGGREGATOR 4P 1369-BGA
Manufacturer:
Cortina Systems Inc
Datasheet: