SI2434-C-GT Silicon Laboratories Inc, SI2434-C-GT Datasheet - Page 30
![no-image](/images/manufacturer_photos/0/6/609/silicon_laboratories_inc_sml.jpg)
SI2434-C-GT
Manufacturer Part Number
SI2434-C-GT
Description
Manufacturer
Silicon Laboratories Inc
Datasheet
1.SI2434-C-GT.pdf
(74 pages)
Specifications of SI2434-C-GT
Main Category
Chipset
Data Rate
32.8125Kbps
Operating Supply Voltage (typ)
3.3V
Operating Supply Voltage (min)
3V
Operating Supply Voltage (max)
3.6V
Operating Temp Range
-40C to 85C
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Lead Free Status / RoHS Status
Supplier Unconfirmed
Si2457/34/15/04
30
&H4
&H5
&H6
&H7
&H8
&H9
&H10
&H11
&Pn
&P0
&P1
&Tn
&T0
&T2
&T3
&T4
&T5
&T6
&Xn
&X0
Command
Table 11. Extended AT& Command Set (Command Defaults in Bold) (Continued)
ITU-T V.32bis with automatic fallback (14.4 kbps to 300 bps) (default for Si2415)
ITU-T V.32bis only (14.4 kbps to 4800 bps)
ITU-T V.22bis only (2400 bps or 1200 bps)
ITU-T V.22 only (1200 bps)
Bell 212 only (1200 bps)
Bell 103 only (300 bps)
ITU-T V.21 only (300 bps)
V.23 (1200/75 bps)
Japan pulse dialing
Configure Si2457/34/15/04 for 10 pulse-per-second pulse dialing. For Japan.
Configure Si2457/34/15/04 for 20 pulse-per-second pulse dialing. For Japan.
Test mode
Cancel test mode (Escape to command mode to issue AT&T0). This command will also report the
number of bit errors encountered on the previous &T4 or &T5 test.
Initiate ITU-T V.54 (ANALOOP) test. Modulation set by &H AT command. Test loop is through the
DSP (Si2457/34/15/04 device) only. ISOmodem® echoes data from TX pin (Register 0 in parallel
mode) back to RX pin (Register 0 in parallel mode).
Initiate ITU-T V.54 (ANALOOP) test. Modulation set by &H AT command. Test loop is through the
DSP (Si2457/34/15/04), DAA interface section (Si2457/34/15/04), DAA interface (Si3018), and ana-
log hybrid circuit (Si3018). ISOmodem echoes data from TX pin (Register 0 in parallel mode) back to
RX pin (Register 0 in parallel mode). Phone line termination required as in Figure 1 . To test only the
link operation, the hybrid and AFE codec can be removed from the test loop by setting the DL bit
(U62, bit 1).
Initiate transmit as originating modem with automatic data generation. Modulation, data rate, and
symbol rate are set by &H, &G, and S41. Data pattern is set by the S40 register. Continues until the
ATH command is sent after an escape into command mode. Data is also demodulated as in
ANALOOP, and any bit errors are counted to be displayed after the test using &T0.
Initiate transmit as answering modem with automatic data generation. Modulation, data rate, and
symbol rate are set by &H, &G, and S41. Data pattern is set by the S40 register. Continues until the
ATH command is sent after an escape into command mode. Data is also demodulated as in
ANALOOP, and any bit errors are counted to be displayed after the test using &T0.
Compute checksum for firmware-upgradeable section of program memory. If no firmware upgrade is
installed, &T6 returns 0x4474.
Automatic determination of telephone line type.
Abort &x1 or &x2 command.
Rev. 1.1
Action