MCZ33742EG Freescale, MCZ33742EG Datasheet - Page 29
![](/photos/31/30/313046/mcz33742eg_sml.jpg)
MCZ33742EG
Manufacturer Part Number
MCZ33742EG
Description
Manufacturer
Freescale
Datasheet
1.MCZ33742EG.pdf
(70 pages)
Specifications of MCZ33742EG
Data Rate
1000Kbps
Number Of Transceivers
1
Standard Supported
CAN 2.0
Operating Supply Voltage (max)
27V
Operating Supply Voltage (typ)
5/9/12/15/18/24V
Operating Supply Voltage (min)
4.5V
Package Type
SOIC W
Supply Current
45mA
Operating Temperature (max)
125C
Operating Temperature (min)
-40C
Operating Temperature Classification
Automotive
Mounting
Surface Mount
Pin Count
28
Lead Free Status / RoHS Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MCZ33742EG
Manufacturer:
FREESCALE
Quantity:
20 000
Part Number:
MCZ33742EGR2
Manufacturer:
FREESCALE
Quantity:
20 000
Table 7. Table of Operations
APPLICATION WAKE-UP FROM THE 33742
from the SBC side. When a wake-up condition is detected by
the SBC (for example, CAN, wake-up input), the 33742
enters the Normal Request mode and generates an interrupt
pulse at the INT pin.
APPLICATION WAKE-UP FROM THE MCU
may come from the system MCU. In this case the MCU
selects the device the using a LOW-to-HIGH transition on the
33742 CS pin. Then the 33742S goes into Normal Request
mode and generates an interrupt pulse at the INT pin.
Analog Integrated Circuit Device Data
Freescale Semiconductor
Notes
Programming
39.
40.
41.
Debug
Debug
Debug
When the application is in Stop mode, it can be awakened
When the device is in the Stop mode, a wake-up event
Request
Standby
Standby
Normal
Normal
Normal
Mode
Sleep
Flash
Stop
Stop
Mode entered via special sequence described under the heading
beginning on page 34.
I
WDOG if enabled.
DD
(39)
(39)
(39)
over-current always enabled.
HS:OFF or Cyclic Sense
Voltage Regulator
HS: OFF or Cyclic
Same as Standby
Forced externally
Same as Normal
HS: Controllable
HS: Controllable
(Limited Current
Same as Stop
HS Switch
Capability),
VDD: OFF,
VDD: ON,
VDD: ON,
VDD: ON,
VDD: ON
V2: OFF,
HS: OFF
V2: OFF,
V2: OFF,
V2: OFF,
V2: ON,
L0 : L3, Cyclic Sense
I
DD
CAN, SPI, L0 : L3,
Forced Wake-up,
Forced Wake-up
Same as Stop
Cyclic Sense,
Capabilities
(if Enabled)
Over-current
CAN, SPI,
Wake-up
–
–
–
–
–
–
(40)
Low for t
Active LOW if WDOG
or VDD under-voltage
or V
under-voltage occurs
under-voltage occurs
under-voltage occurs
Active LOW if VDD
Active LOW if VDD
Active LOW if VDD
Same as Normal
Normally HIGH.
Normally HIGH.
Normally HIGH.
Normally HIGH.
Normally HIGH.
Active LOW if
Not operating
DD
then HIGH
WDOG
RST Pin
under-voltage
occurs
occurs
mode
Debug Mode: Hardware and Software Debug with the
LOW
RST
STOP MODE CURRENT MONITOR
(I
mode and generates an interrupt at the INT pin. The interrupt
is a non-maskable and the INTR register will have no flag set.
INTERRUPT GENERATION WHEN WAKE-UP
FROM STOP MODE
Normal Request mode before generating a 10 μs typical
pulse on the INT pin. These are non-maskable interrupts with
the wake-up event read through the SPI registers, the
CANWU bit in the CAN Register (CANR), or the LCTRx bit in
the Wake-up Register (WUR). In case of wake-up from Stop
DDS-WU
DUR
If the VDD output current exceeds an internal set threshold
When the SBC wakes from Stop mode, it first enters the
(41)
time,
), the SBC automatically enters the Normal Request
Same as Standby Not running
If enabled, signal
Temp, CAN, HS)
Same as Normal
Same as Normal
(not maskable)
Signal 33742S
Same as Stop
I
Not operating
wake-up and
DD
failure (VDD
Pre-warning
Not Active
INT Pin
> I
mode
–
DDS-WU
FUNCTIONAL DEVICE OPERATION
Not running if
Not operating
Not running
Not running
Not running
Watchdog
Running if
Software
enabled.
Running
Running
disabled
–
OPERATIONAL MODES
Wake-up capability
Wake-up capability
Same as Standby
Same as Normal
Same as Stop
Not operating
Low power.
Low power.
Low power
TXD / RXD
CAN Cell
if enabled
if enabled
33742,
–
33742
29