AM 1601-7RG POWER ONE, AM 1601-7RG Datasheet - Page 19

• Manufacturer Part Number: AM 1601-7RG
• Manufacturer: POWER ONE
• Type: Non-Inv/StpUp/StpDwnr

Specifications of AM 1601-7RG

• Output Current: 2A
• Input Voltage: 15V
• Output Voltage: 24V
• Output Power: 50
• Screening Level: Commercial
• Operating Temperature Min Deg. C: -25C
• Operating Temperature Max Deg. C: 71C
• Product Length (mm): 168.5mm
• Product Depth (mm): 111.2mm
• Product Height (mm): 38.7mm
• Mounting Style: Din-Rail
• Pin Count: 11
• Number Of Outputs: 1
• Lead Free Status / RoHS Status: Compliant

Description of Options
Table 17: Survey of options
Table 18: Configuration of option A and option P
- 7 Former Standard Temperature Range
Option -7 stays for the operational ambient temperature range
from –25 to 71 °C, which may be preferred by some customers
for reasons of documentation or approvals.
A Test Sockets
Test sockets (pin Ø = 2 mm, distance d = 5.08 mm) are located
at the front of the converter. The output voltage is sensed at the
connector pins inside of the converter. Outputs 2 and 3 of
triple-output models are not sensed.
P Potentiometer
Built-in multi-turn potentiometers provide an output voltage
adjustment range of minimum ± 5% of V
accessible through holes in the front cover. Compensation of
voltage drop across connector and wiring becomes easily
achievable. For output voltages V
voltage
proportionally to V
adjustment of V
E Electronic Inrush Current Limitation
Available for CM, EM and LM models.
The standard version of the models CM, DM, EM and LM
include a passive inrush current limitation with an NTC resistor.
For applications, which require an improved inrush current
BCD20018 Rev AB
1
2
3
Type of option
Potentiometer
Test sockets
1
Note:
applications.
Option
Models equipped with option P do not provide the R function; pins 14 and 17 are not connected.
Option D excludes option V and vice versa
Only available if main output voltage V
Models equipped with option P do not provide the R function; pins 14 and 17 are not connected.
V
D
P
-7
A
E
F
H
2 3
1
2
Potentiometers
according
Function of option
Former standard operational ambient temperature range
Test sockets at front panel for check of output voltage
Electronic inrush current limitation circuitry
Potentiometer for fine adjustment of output voltage
Input fuse built-in inside case
Enhanced output to case electric strength test voltage
Input and/or output undervoltage monitoring circuitry
Input and/or output undervoltage monitoring circuitry
1
o1
.
o
/V
o nom
to Electrical
®
are
. Triple-output models allow only the
not
AM
o
> V
Output 1
recommended
–
yes
yes
o1
Input
LM1000
o nom
= 5.1 V
, the minimum input
Data
o nom
for
increases
and are
mobile
Page 19 of 26
Output 1
yes
yes
AM
limitation, an active electronic circuit as shown in fig. Option E
block diagram has been developed. Typical inrush current
waveforms of units equipped with this option are shown below.
CM models meet the CEPT/ETSI standards for 48 V supply
voltage according to ETS 300132-2, if fitted with option E
combined with option D6 (input voltage monitoring). Option D6,
externally adjustable via potentiometer, is necessary to disable
the converter at input voltages below the actual service
ranges, avoiding an excessive input current when the input
voltage is raised slowly according to ETS 300132-2. Option D6
threshold level V
be adjusted to 36 – 40.5 V for 48 V nominal supply voltage (for
60 V systems, threshold should be set to 44 – 50 V). The D
output (pin 5) should be connected to the inhibit (pin 2). For
applications, where potentiometers are not allowed, refer to
option D9.
Fig. 18
Option E block diagram
Characteristic
T
V
Active inrush current limitation for CM, EM, LM models
Adjustment range ±5% of V
Fuse not externally accessible
See table Isolation
Safe data signal output (D0 – D9)
ACFAIL signal according to VME specifications (V0, V2, V3)
A
o
–
= – 25 to 71°C
internally measured at the connector terminals
50 Watt DC-DC and AC-DC Converters
LM2000
Output 2
yes
yes
(LM models)
Rectifier
t i
+ V
h i
(refer to description of option D) should
Output 1
o nom
yes
yes
, excludes R input
Control logic
M Series Data Sheet
R
S
AM
Output 2
R
FET
–
I
www.power-one.com
no
no
LM3000
C
i
11018a
Output 3
no
no