XC3S500E-4PQ208I Xilinx Inc, XC3S500E-4PQ208I Datasheet - Page 87
![no-image](/images/no-image-200.jpg)
XC3S500E-4PQ208I
Manufacturer Part Number
XC3S500E-4PQ208I
Description
FPGA Spartan®-3E Family 500K Gates 10476 Cells 572MHz 90nm (CMOS) Technology 1.2V 208-Pin PQFP
Manufacturer
Xilinx Inc
Series
Spartan™-3Er
Datasheet
1.XC3S100E-4VQG100C.pdf
(233 pages)
Specifications of XC3S500E-4PQ208I
Package
208PQFP
Family Name
Spartan®-3E
Device Logic Cells
10476
Device Logic Units
1164
Device System Gates
500000
Number Of Registers
9312
Maximum Internal Frequency
572 MHz
Typical Operating Supply Voltage
1.2 V
Maximum Number Of User I/os
158
Ram Bits
368640
Number Of Logic Elements/cells
10476
Number Of Labs/clbs
1164
Total Ram Bits
368640
Number Of I /o
158
Number Of Gates
500000
Voltage - Supply
1.14 V ~ 1.26 V
Mounting Type
Surface Mount
Operating Temperature
-40°C ~ 100°C
Package / Case
208-BFQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
XC3S500E-4PQ208I
Manufacturer:
XILINX
Quantity:
364
Part Number:
XC3S500E-4PQ208I
Manufacturer:
XILINX/赛灵思
Quantity:
20 000
This addressing flexibility allows the FPGA to share the par-
allel Flash PROM with an external or embedded processor.
Depending on the specific processor architecture, the pro-
cessor boots either from the top or bottom of memory. The
FPGA is flexible and boots from the opposite end of mem-
ory from the processor. Only the processor or the FPGA can
boot at any given time. The FPGA can configure first, hold-
ing the processor in reset or the processor can boot first,
asserting the FPGA’s PROG_B pin.
The mode select pins, M[2:0], are sampled when the
FPGA’s INIT_B output goes High and must be at defined
logic levels during this time. After configuration, when the
FPGA’s DONE output goes High, the mode pins are avail-
able as full-featured user-I/O pins.
enable pull-up resistors on all user-I/O pins or High to dis-
able the pull-up resistors. The HSWAP control must remain
at a constant logic level throughout FPGA configuration.
After configuration, when the FPGA’s DONE output goes
High, the HSWAP pin is available as full-featured user-I/O
pin and is powered by the VCCO_0 supply.
Table 59: Byte-Wide Peripheral Interface (BPI) Connections
DS312-2 (v3.8) August 26, 2009
Product Specification
HSWAP
M[2:0]
CSI_B
RDWR_B
LDC0
P
A
Pin Name
P
Similarly, the FPGA’s HSWAP pin must be Low to
R
FPGA Direction
Output
Input
Input
Input
Input
User I/O Pull-Up Control. When
Low during configuration, enables
pull-up resistors in all I/O pins to
respective I/O bank V
0: Pull-ups during configuration
1: No pull-ups
Mode Select. Selects the FPGA
configuration mode. See
Considerations for the HSWAP,
M[2:0], and VS[2:0]
Chip Select Input. Active Low.
Read/Write Control. Active Low
write enable. Read functionality
typically only used after
configuration, if bitstream option
Persist=Yes.
PROM Chip Enable
Description
Pins.
CCO
www.xilinx.com
Design
input.
The RDWR_B and CSI_B must be Low throughout the con-
figuration process. After configuration, these pins also
become user I/O.
In a single-FPGA application, the FPGA’s CSO_B and
CCLK pins are not used but are actively driving during the
configuration process. The BUSY pin is not used but also
actively drives during configuration and is available as a
user I/O after configuration.
After configuration, all of the interface pins except DONE
and PROG_B are available as user I/Os. Furthermore, the
bidirectional SelectMAP configuration peripheral interface
(see
To continue using SelectMAP mode, set the
stream generator option to Yes. An external host can then
read and verify configuration data.
The Persist option will maintain A20-A23 as configuration
pins although they are not used in SelectMAP mode.
Drive at valid logic level
throughout configuration.
M2 = 0, M1 = 1. Set M0 = 0 to
start at address 0, increment
addresses. Set M0 = 1 to start at
address 0xFFFFFF and
decrement addresses. Sampled
when INIT_B goes High.
Must be Low throughout
configuration.
Must be Low throughout
configuration.
Connect to PROM chip-select
input (CE#). FPGA drives this
signal Low throughout
configuration.
Slave Parallel
During Configuration
Mode) is available after configuration.
Functional Description
User I/O
User I/O
User I/O. If bitstream
option Persist=Yes,
becomes part of
SelectMap parallel
peripheral interface.
User I/O. If bitstream
option Persist=Yes,
becomes part of
SelectMap parallel
peripheral interface.
User I/O. If the FPGA does
not access the PROM after
configuration, drive this pin
High to deselect the
PROM. A[23:0], D[7:0],
LDC[2:1], and HDC then
become available as user
I/O.
After Configuration
Persist
bit-
87