NDS02ZG-M6G POWER ONE, NDS02ZG-M6G Datasheet
NDS02ZG-M6G
Specifications of NDS02ZG-M6G
Related parts for NDS02ZG-M6G
NDS02ZG-M6G Summary of contents
Page 1
... NDS03ZB-M6 36 – NDS03ZD-M6 36 – NDS03ZE-M6 36 – NDS02ZG-M6 36 – For products RoHS-compliant for all 6 substances, change the suffix -M6 to -M6G. Model numbers highlighted in yellow are not recommended for new designs BCD.00013 Rev. AB, 26-Aug-2010 10 W SMT DC-DC Converters, 1.5 – Output Features • ...
Page 2
Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings may cause performance degradation, adversely affect long- term reliability and cause permanent damage to the converter. Specifications apply over specified input voltage, output load and temperature range, unless otherwise ...
Page 3
Output Data All specifications apply over input voltage, output load, and temperature range, unless otherwise noted. NDS03ZA : 1.5 V/3.0 A Parameter Output Voltage V o Setpoint Accuracy Output Current I o Line Regulation Load Regulation Dynamic Regulation: Peak Deviation ...
Page 4
All specifications apply over input voltage, output load, and temperature range, unless otherwise noted. NDS03ZB : 1.8 V/3.0 A Parameter Output Voltage V o Setpoint Accuracy Output Current I o Line Regulation Load Regulation Dynamic Regulation Peak Deviation Settling Time ...
Page 5
All specifications apply over input voltage, output load and temperature range, unless otherwise noted. NDS03ZD : 2.5 V/ 3.0A Parameter Output Voltage V o Setpoint Accuracy Output Current I o Line Regulation Load Regulation Dynamic Regulation Peak Deviation Settling Time ...
Page 6
All specifications apply over input voltage, output load and temperature range, unless otherwise noted. NDS03ZE : 3.3 V/3.0 A Parameter Output Voltage V o Setpoint Accuracy Output Current I o Line Regulation Load Regulation Dynamic Regulation Peak Deviation Settling Time ...
Page 7
... All specifications apply over input voltage, output load and temperature range, unless otherwise noted. NDS02ZG : 5.0 V/2.0 A Parameter Output Voltage V o Setpoint Accuracy Output Current I o Line Regulation Load Regulation Dynamic Regulation Peak Deviation Settling Time Output Voltage Ripple Admissible Load ...
Page 8
Shutdown Parameter Shutdown Control: Converter OFF Converter ON Sink Current Temperature Derating Curves The derating curves below give an indication of the output power achievable with and without forced-air cooling. However in the final application, in order to ensure the ...
Page 9
... Rext = (( Where V o Model NDS03ZA NDS03ZB NDS03ZD NDS03ZE NDS02ZG ). To c Note: When the output voltage is trimmed up, the output power from the converter must not exceed its maximum rating. This is determined by measuring the allowable case voltage on the output pins, and multiplying it by the output current ...
Page 10
Safety These converters are tested with 1500 VDC from input to output. The input-to-output resistance is greater than 10 MΩ. These converters are provided with Basic Insulation between input and output. Nevertheless, if the system using the converter needs to ...
Page 11
Mechanical Data Dimensions in mm [inches] BCD.00013 Rev. AB, 26-Aug-2010 NDS Series Data Sheet 10 W SMT DC-DC Converters, 1.5 – Output Page www.power-one.com ...
Page 12
Surface Mount Assembly Soldering The following soldering instructions must be observed to prevent failure or significant degradation of the module performance. Power-One will not honor any warranty claims arising from failure to observe these instructions. The lead-frame is constructed for ...
Page 13
Pick & Place Assembly The product is designed with a large flat area in the center of the top surface to serve as a pick up point for automated vacuum pick and place equipment. The ‘open board’ construction of the ...
Page 14
Pin Allocation Pin Designation 1 Shutdown 2 - pin 5 No pin 6 No pin 7 No pin 8 No pin Trim 13 + ...