P87C552SBAA NXP Semiconductors, P87C552SBAA Datasheet - Page 6

• Manufacturer Part Number: P87C552SBAA
• Description: MCU 8-Bit 87C 80C51 CISC 8KB EPROM 3.3V/5V 68-Pin PLCC Tube
• Manufacturer: NXP Semiconductors

Specifications of P87C552SBAA

• Package: 68PLCC
• Device Core: 80C51
• Family Name: 87C
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 8 Bit
• Number Of Programmable I/os: 40
• Interface Type: I2C/UART
• On-chip Adc: 8-chx10-bit
• Number Of Timers: 3
• Ram Size: 256 Byte
• Program Memory Size: 8 KB
• Program Memory Type: EPROM
• Operating Temperature: 0 to 70 °C

1. To avoid “latch-up” effect at power-on, the voltage on any pin at any time must not be higher or lower than V
Philips Semiconductors
PIN DESCRIPTION (Continued)
NOTE:
2003 Apr 01
P4.0-P4.7
P5.0-P5.7
RST
XTAL1
XTAL2
V
PSEN
ALE/PROG
EA/V
AV
AV
AV
AV
MNEMONIC
SS
80C51 8-bit microcontroller
8K/256 OTP, 8 channel 10 bit A/D, I
capture/compare, high I/O, low voltage (2.7 V to 5.5 V), low power
respectively.
REF–
REF+
SS
DD
PP
68-62,
PLCC
13, 14
36, 37
7-14
7-12
15
35
34
47
48
49
58
59
60
61
1
1
PIN NO.
80, 1-2
80, 1-2
71-64
34-36
QFP
7, 8
4-8
4-6
32
31
48
49
50
59
60
61
63
9
TYPE
I/O
I/O
O
O
O
O
O
I
I
I
I
I
I
I
I
CMT0, CMT1 (P4.6, P4.7): Timer T2 compare and toggle outputs on a match with timer T2.
Port 4: 8-bit programmable I/O port. Alternate functions include:
CMSR0-CMSR5 (P4.0-P4.5): Timer T2 compare and set/reset outputs on a match with
timer T2.
Port 4 has four modes selected on a per bit basis by writing to the P4M1 and P4M2
registers as follows:
Port 5: 8-bit input port.
ADC0-ADC7 (P5.0-P5.7): Alternate function: Eight input channels to the ADC.
Reset: Input to reset the 87C552. It also provides a reset pulse as output when timer T3
overflows.
Crystal Input 1: Input to the inverting amplifier that forms the oscillator, and input to the
internal clock generator. Receives the external clock signal when an external oscillator is
used.
Crystal Input 2: Output of the inverting amplifier that forms the oscillator. Left open-circuit
when an external clock is used.
Digital ground.
Program Store Enable: Active-low read strobe to external program memory.
Address Latch Enable: Latches the low byte of the address during accesses to external
memory. It is activated every six oscillator periods. During an external data memory
access, one ALE pulse is skipped. ALE can drive up to eight LS TTL inputs and handles
CMOS inputs without an external pull-up. This pin is also the program pulse input (PROG)
during EPROM programming.
External Access: When EA is held at TTL level high, the CPU executes out of the internal
program ROM provided the program counter is less than 8,192. When EA is held at TTL
low level, the CPU executes out of external program memory. EA is not allowed to float.
This pin also receives the 12.75V programming supply voltage (V
programming.
Analog to Digital Conversion Reference Resistor: Low-end.
Analog to Digital Conversion Reference Resistor: High-end.
Analog Ground
Analog Power Supply
2
C, PWM,
P4M1.x
0
0
1
1
P4M2.x
0
1
0
1
6
Mode Description
Pseudo-bidirectional (standard c51 configuration; default)
Push-Pull
High impedance
Open drain
NAME AND FUNCTION
DD
+ 0.5V or V
PP
) during EPROM
SS
– 0.5V,
P87C552
Product data