601966-4 Tyco Electronics, 601966-4 Datasheet - Page 16
![Connector Accessories Loose Piece Tool Positioner](/photos/9/89/98915/601966-4_sml.jpg)
601966-4
Manufacturer Part Number
601966-4
Description
Connector Accessories Loose Piece Tool Positioner
Manufacturer
Tyco Electronics
Type
Positionerr
Specifications of 601966-4
Accessory Type
Positioner
Product
Tool Component
Lead Free Status / RoHS Status
Not applicable / Not applicable
For Use With/related Products
A9977
For Use With
206071-4 - CONN SOCKET 22-28AWG CRIMP AU204351-5 - CONN SOCKET 22-28AWG CRIMP AU204351-4 - CONN SOCKET 22-28AWG CRIMP AUA34487 - CONN SOCKET 26-28AWG 50GOLDA34527 - CONN SOCKET 22-28AWG CRIMP GOLDA34486 - CONN SOCKET 22-28AWG 50GOLD
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
A34489
16 of 17
S
(MIL- - C- - 22520/2- - 01)
(MIL C 22520/1 01)
(MIL- - C- - 22520/1- - 01)
Use for periodic general inspection. The plug gages listed in
Figure 8 conform to these gage element diameters.
(Military Spec)
(Military Spec)
and 608668--1
and 608668- - 1
601966--1
601966 1
608651 1
608651--1
601967--1
601966--1
601967--1
608668--1
608651--1
GO Dia
TOOL
TOOL
For Periodic General Inspection
Suggested Plug Gage Design
SELECTOR
SELECTOR
SELECTOR
6.35 [.250] Min Typ
SETTING
SETTING
TOOL
TOOL
D8S
D4S
D4S
1
2
3
4
5
6
7
1
2
3
5
6
7
8
1
2
3
5
6
7
8
8
4
4
4
Figure 7
Figure 8
D0.99 [.039]S D1.12 [.044]S
D2.16 [.085]S D2.41 [.095]S
D0.99 [.039]S D1.12 [.044]S
DIAMETER +0.003 [.0001]
0.33 [.013]
0.41 [.016]
0.48 [.019]
0.56 [.022]
0.66 [.026]
0.76 [.030]
0.86 [.034]
1.78 [.070]
1.91 [.075]
2.03 [.080]
2.34 [.092]
2.51 [.099]
2.74 [.108]
0.71 [.028]
0.81 [.032]
0.91 [.036]
1.14 [.045]
1.32 [.052]
1.50 [.059]
1.73 [.068]
3.00 [.118]
(MIL--C--22520/3--01)
(MIL--C--22520/3--01)
GO
GAGE ELEMENT
(Military Spec)
PLUG GAGE
601968 1
601968--1
601968--3
NO- - GO Dia
0.46 [.018]
0.53 [.021]
0.61 [.024]
0.69 [.027]
0.79 [.031]
0.89 [.035]
0.99 [.039]
2.03 [.080]
2.16 [.085]
2.29 [.090]
2.59 [.102]
2.77 [.109]
3.00 [.118]
3.25 [.128]
0.84 [.033]
0.94 [.037]
1.04 [.041]
1.27 [.050]
1.45 [.057]
1.63 [.064]
1.85 [.073]
NO- - GO
To inspect the crimp height, proceed as follows:
SELECTOR
SETTING
GO element must pass
completely through the die
opening.
1. Crimp the contact according to Section 3,
CRIMPING PROCEDURE.
2. Measure across opposite indents in the contact,
then rotate the contact 90 degrees, and measure
again. See Figure 10. DO NOT go beyond initial
contact as this could cause a depression and result
in an inaccurate reading.
TOOL
TOOL
Crimped
Contact
1
2
3
4
5
6
7
8
GO
Element
0.406--0.533 [.016--.021]
0.483--0.610 [.019--.024]
0.559--0.686 [.022--.027]
0.635--0.762 [.025--.030]
0.737--0.864 [.029--.034]
0.838--0.965 [.033--.038]
0.940--1.067 [.037--.042]
1.067--1.194 [.042--.047]
MIL- - C- - 22520/2- - 01
TOOL 601966- - 1
Gaging the Die Opening
Crimp Height Inspection
Military Spec
Die
Opening
Figure 10
Figure 9
CRIMP HEIGHT
CRIMP HEIGHT
Crimp
Height
NO- - GO element may enter
partially, but must not pass
completely through the die
opening.
0.813--0.940 [.032--.037]
0.914--1.041 [.036--.041]
1.016--1.143 [.040--.045]
1.092--1.219 [.043--.048]
1.245--1.372 [.049--.054]
1.422--1.549 [.056--.061]
1.600--1.727 [.063--.068]
1.829--1.956 [.072--.077]
MIL- - C- - 22520/1- - 01
TOOL 601967- - 1
Military Spec
NO- - GO
Element
408- 7516
Rev E