BFC236652473 Vishay, BFC236652473 Datasheet - Page 16

• Manufacturer Part Number: BFC236652473
• Description: Cap Film 0.047uF 400VDC/220VAC PET 5% 10 X 5 X 13.5mm RDL 7.5mm Loose in Box
• Manufacturer: Vishay
• Series: MKT 366r

Specifications of BFC236652473

• Package/case: 10(Max) X 5(Max) X 13.5(Max)
• Mounting: Through Hole
• Capacitance Value: 0.047 uF
• Voltage: 400|220 Vdc|Vac
• Dielectric: PET
• Lead Pitch For Radial: 7.5 mm
• Product Length: 10(Max) mm
• Product Depth: 5(Max) mm
• Tolerance: 5 %
• Operating Temperature: -55 to 105 °C
• Capacitance: 0.047 uF
• Voltage Rating: 400 Volts
• Termination Style: Radial
• Dimensions: 5 mm Dia. x 4 mm W x 10 mm L x 12 mm H
• Lead Spacing: 7.5 mm
• Operating Temperature Range: 0 C to + 85 C
• Dissipation Factor Df: 75
• Product: Metallized Polyester Film Capacitors
• Lead Free Status / Rohs Status: Details

MKT365, MKT366, MKT367
Vishay BCcomponents
5. The maximum component surface temperature rise must be lower than the limits (see graph “Max. allowed component
6. Since in circuits used at voltages over 280 V peak-to-peak the risk for an intrinsically active flammability after a capacitor
7. When using these capacitors as across-the-line capacitor in the input filter for mains applications or as series connected with
VOLTAGE CONDITIONS FOR 6 ABOVE
EXAMPLE
C = 330 nF - 63 V used for the voltage signal shown in next drawing.
U
The ambient temperature is 35 °C
Checking conditions:
1. The peak voltage U
2. The peak-to-peak voltage 40 V is lower than 2 2 x 40 V
3. The voltage pulse slope (dU/dt) = 40 V/100 µs = 0.4 V/µs
4. The dissipated power is 16.2 mW as calculated with fourier terms
5. Not applicable
6. Not applicable
Voltage Signal
www.vishay.com
44
P-P
ALLOWED VOLTAGES
Maximum continuous RMS voltage
Maximum temperature RMS-overvoltage (< 24 h)
Maximum peak voltage (V
temperature rise”).
breakdown (short circuit) increases, it is recommended that the power to the component is limited to 100 times the values
mentioned in the table: “Heat Conductivity”
an impedance to the mains the applicant must guarantee that the following conditions are fulfilled in any case (spikes and
surge voltages from the mains included).
This is lower than 110 V/µs (see specific reference data for each version)
The temperature rise for W
This is lower than 15 °C temperature rise at 35 °C, according figure “Max. allowed component temperature rise”
= 40 V; U
P
= 35 V; T
P
Voltage
O-P
= 35 V is lower than 63 V
1
= 100 µs; T
U
) (< 2 s)
P
max.
= 4.5 mm and pitch = 5 mm will be 16.2 mW/2.5 mW/°C = 6.5 °C
For technical questions, contact:
2
T
1
= 200 µs
MKT Radial Lacquered Type
T
2
DC Film Capacitors
DC
U
P-P
AC
= 113 U
[e-mail]
T
1.25 x U
1.6 x U
amb
P-P
U
RAC
85 °C
RDC
RAC
Time
85 °C < T
Document Number: 28102
0.8 x U
1.3 x U
U
amb
RAC
Revision: 22-Dec-10
RAC
RDC
105 °C