HI1-0201HS/883 Intersil, HI1-0201HS/883 Datasheet - Page 7

• Manufacturer Part Number: HI1-0201HS/883
• Description: Analog Switch Quad SPST 16-Pin CDIP
• Manufacturer: Intersil
• Type: Analog Switchr

Specifications of HI1-0201HS/883

• Package: 16CDIP
• Maximum On Resistance: 50@±15V Ohm
• Maximum High Level Output Current: 25 mA
• Maximum Turn-on Time: 50@±15V ns
• Switch Architecture: SPST
• Power Supply Type: Dual

DSCC FORM 2234
APR 97
1/ The limiting terms “min” (minimum) and “max” (maximum) shall be considered to apply to magnitudes only. Negative current
shall be defined as conventional current flow out of a device terminal.
2/ These parameters may not be tested, but shall be guaranteed to the limits specified in table I herein.
3/ Test not required if applied as a forcing function.
4/ Subgroup 4 (C
which may affect capacitance.
as listed in MIL-HDBK-103. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the
manufacturer has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator
shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M
shall be in accordance with MIL-PRF-38535, appendix A.
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see
6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing
shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or
for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
involving devices acquired to this drawing is required for any change as defined in MIL-PRF-38535, appendix A.
option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made available
onshore at the option of the reviewer.
group number 82 (see MIL-PRF-38535, appendix A).
Capacitance address
Capacitance input switch
Capacitance output
switch
Off isolation
Crosstalk between
channels
Charge transfer error
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed
3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for
3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein)
3.9 Verification and review for device class M. For device class M, DSCC, DSCC's agent, and the acquiring activity retain the
3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit
DEFENSE SUPPLY CENTER COLUMBUS
Test
MICROCIRCUIT DRAWING
COLUMBUS, OHIO 43216-5000
A
, C
IS
, and C
STANDARD
C
C
V
V
V
C
Symbol
ISO
CT
CTE
OS
IS
OS
A
measurements) shall be measured only for the initial test and after process or design changes
TABLE I. Electrical performance characteristics – Continued.
V+ = +15 V dc, V- = -15 V dc
unless otherwise specified
GND = 0 V, V
f = 1 MHz, T
GND = 0 V, V
f = 1 MHz, T
GND = 0 V, V
f = 1 MHz, T
V
T
V
T
T
A
A
A
GEN
GEN
= +25 C
= +25 C
= +25 C
-55 C
= 1 V
= 1 V
Conditions
P-P
P-P
T
A
A
A
, f = 100 kHz,
, f = 100 kHz,
A
IL
IH
IH
= +25 C
= +25 C
= +25 C
2/
2/
2/
= 0 V,
= 5 V,
= 5 V,
+125 C
4/
4/
4/
SIZE
A
subgroups
Group A
4
4
4
4
4
4
REVISION LEVEL
Device
type
All
All
All
All
All
All
D
60
60
Min
Limits 1/
15
15
20
10
Max
SHEET
5962-86716
dB
dB
mV
pF
pF
pF
7
Unit