AC3006 ROTRONIC, AC3006 Datasheet
![no-image](/images/no-image-200.jpg)
AC3006
Specifications of AC3006
AC3006 Summary of contents
Page 1
... Software overview The new ROTRONIC devices are equipped with a practical interface for configuration of the devices and for the display and recording of data. The ROTRONIC HW4 software is one of the most comprehensive and user-friendly validated software packages available on the market today not possible to describe the functionality of the software in full detail here. ...
Page 2
... For this they need software and devices that can be validated. Combining ROTRONIC's HW4-compatible devices and HW4 software, ROTRONIC supplies a solution in which validation plays a central role. The devices and software are validated and compatible with FDA 21 CFR Part 11 (directive of the US Food and Drug Administration, FDA) and GxP. DS-NT4, DS-NT4-WL, DS-U1 ...
Page 3
... Analysis and calculation tool/Psychrometric calculations All ROTRONIC devices measure relative humidity in %rh and temperature in °C/°F. These two values can be used to calculate other psychrometric values such as dew point, mixing ratio, enthalpy and wet-bulb temperature. The calculation module of the HW4 software uses WMO* verified formulas for these calculations and allows the user to define their own parameters (e.g. mixing ratio ratio & ...
Page 4
Statistical functions For many users detailed data, which can be very extensive, is not necessarily of much interest. For them it is merely important that the measured values lie within a certain range. This is the role of the statistical ...
Page 5
... The long term stability of ROTRONIC probes is better than 1%rh per year under normal conditions. Normal conditions exist when the concentration of contaminants/pollutants in the air does not exceed maximum allowable concentration (MAC) levels. ...
Page 6
... SCS* humidity standards ROTRONIC humidity standards are delivered in packs of five ampoules of the same humidity value. Every ampoule is marked with its humidity value and a serial number. The most frequently used values are 35 and 80 %rh, which are used for two-point calibrations. All ampoules except for the 0 %rh standard contain an unsaturated salt solution ...
Page 7
... Calibration devices ROTRONIC calibration devices are small, airtight chambers that precisely fit ROTRONIC probes. The lower part of the device consists of a screw-on lid into which the humidity standard is poured onto an absorbent textile pad. The specified humidity is generated in the calibration device after a stabilisation period of 30...180 minutes. The probe can then be calibrated or adjusted in comparison with the reference value of the humidity standard ...
Page 8
Filters We have a range of filters available for optimum protection of the sensors. By choosing the right filter, you will obtain optimum performance regarding sensor protection and probe response times. Technical data and order information for filters Order ...
Page 9
Technical data and order information for filter spare parts Order code Probe HC2-IC probes NSP-ME HC2-IM and SP-MSB15 HC2-IE probes SP-M15 All industrial probes SP-S15 All industrial probes SP-T15 All industrial probes Passive connection cables Order code Use / Info ...
Page 10
... Replaces MOK-xx-WIN AC3003 Signal amplifier set for HygroClip2 probes AC3005 Connects HygroClip2 probes to an Ethernet network. Requires AC adaptor AC1211 AC3006 Connects AirChip3000 devices HW4 For direct RS232 connection AC3007 Requires mains adapter AC1207 (9 VDC) AC3009 Active converter cable for AC3000 devices ...
Page 11
Technical data and order information Mounting hardware AC5001 Adapter for 15 mm probes holes For mounting of HF4x, HF5X, HF6X, AC5002 transmitters on top hat rail AC5003 AC5004 HF4, HF5, HF6, HP2X For temperatures <100 °C AC5005 ...