LAN91C100FD-ST SMSC, LAN91C100FD-ST Datasheet - Page 30
![no-image](/images/manufacturer_photos/0/6/617/smsc_sml.jpg)
LAN91C100FD-ST
Manufacturer Part Number
LAN91C100FD-ST
Description
Ethernet ICs Non-PCI 10/100 Ethernet MAC
Manufacturer
SMSC
Type
Single Chip MAC and PHY Controllerr
Datasheet
1.LAN91C100FD-ST.pdf
(77 pages)
Specifications of LAN91C100FD-ST
Ethernet Connection Type
10 Base-T, 100 Base-TX
Minimum Operating Temperature
0 C
Mounting Style
SMD/SMT
Product
Ethernet Controllers
Number Of Transceivers
1
Standard Supported
802.3
Data Rate
10 MB, 100 MB
Supply Voltage (max)
7 V
Supply Voltage (min)
0.3 V
Supply Current (max)
40 mA
Maximum Operating Temperature
+ 70 C
Package / Case
TQFP-208
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Note:
Note:
BANK2
Revision 1.0 (09-22-08)
OFFSET
RCV_BAD - When set, bad CRC packets are received. When clear bad CRC packets do not generate
interrupts and their memory is released.
nRXDISC, when asserted, overrides RCV_BAD. Also, RCV_ BAD does not modify the function of RCV
DISCARD in the RCV register.
AUTO RELEASE - When set, transmit pages are released by transmit completion if the transmission was
successful (when TX_SUC is set). In that case there is no status word associated with its packet number,
and successful packet numbers are not even written into the TX COMPLETION FIFO. A sequence of
transmit packets will generate an interrupt only when the sequence is completely transmitted (TX EMPTY
INT will be set), or when a packet in the sequence experiences a fatal error (TX INT will be set). Upon a
fatal error TXENA is cleared and the transmission sequence stops. The packet number that failed, is
present in the FIFO PORTS register, and its pages are not released, allowing the CPU to restart the
sequence after corrective action is taken.
LE ENABLE - Link Error Enable. When set it enables the LINK_OK bit transition as one of the interrupts
merged into the EPH INT bit. Clearing the LE ENABLE bit after an EPH INT interrupt, caused by a
LINK_OK transition, will acknowledge the interrupt. LE ENABLE defaults low (disabled).
CR ENABLE - Counter Roll over Enable. When set, it enables the CTR_ROL bit as one of the interrupts
merged into the EPH INT bit. Reading the COUNTER register after an EPH INT interrupt caused by a
counter rollover, will acknowledge the interrupt. CR ENABLE defaults low (disabled).
TE ENABLE - Transmit Error Enable. When set it enables Transmit Error as one of the interrupts merged
into the EPH INT bit. An EPH INT interrupt caused by a transmitter error is acknowledged by setting
TXENA bit in the TCR register to 1 or by clearing the TE ENABLE bit. TE ENABLE defaults low (disabled).
Transmit Error is any condition that clears TXENA with TX_SUC staying low as described in the EPHSR
register.
EEPROM SELECT - This bit allows the CPU to specify which registers the EEPROM RELOAD or STORE
refers to. When high, the General Purpose Register is the only register read or written. When low,
RELOAD reads Configuration, Base and Individual Address, and STORE writes the Configuration and
Base registers.
RELOAD - When set it will read the EEPROM and update relevant registers with its contents. Clears upon
completing the operation.
STORE - When set, stores the contents of all relevant registers in the serial EEPROM. Clears upon
completing the operation.
When an EEPROM access is in progress the STORE and RELOAD bits will be read back as high. The
remaining 14 bits of this register will be invalid. During this time attempted read/write operations, other
than polling the EEPROM status, will NOT have any effect on the internal registers. The CPU can resume
accesses to the LAN91C100FD after both bits are low. A worst case RELOAD operation initiated by
RESET or by software takes less than 750 μs.
This register is used by the CPU to control the memory allocation, de-allocation, TX FIFO and RX FIFO
control.
0
MMU COMMAND
REGISTER
NAME
DATASHEET
Page 30
BUSY Bit Readable
WRITE ONLY
TYPE
FEAST Fast Ethernet Controller with Full Duplex Capability
SMSC LAN91C100FD Rev. D
SYMBOL
MMUCR