ISPGDX240VA-7BN388 Lattice, ISPGDX240VA-7BN388 Datasheet - Page 4

• Manufacturer Part Number: ISPGDX240VA-7BN388
• Description: Analog & Digital Crosspoint ICs PROGRAMMABLE GEN DIG CROSSPOINT
• Manufacturer: Lattice

Specifications of ISPGDX240VA-7BN388

• Mounting Style: SMD/SMT
• Number Of Arrays: 1
• Operating Supply Voltage: 3.3 V
• Supply Type: Single
• Configuration: 240 x 240
• Package / Case: PLCC-28
• Input Level: TTL
• Output Level: TTL
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 3 V
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Product: Digital Crosspoint
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Flexible mapping of MUXsel
change the MUX select assignment after the ispGDXVA
device has been soldered to the board. Figure 1 shows
that the I/O cell can accept (by programming the appro-
priate fuses) inputs from the MUX outputs of four adjacent
I/O cells, two above and two below. This enables cascad-
ing of the MUXes to enable wider (up to 16:1) MUX
implementations.
The I/O cell also includes a programmable flow-through
latch or register that can be placed in the input or output
path and bypassed for combinatorial outputs. As shown
in Figure 1, when the input control MUX of the register/
latch selects the “A” path, the register/latch gets its inputs
from the 4:1 MUX and drives the I/O output. When
selecting the “B” path, the register/latch is directly driven
by the I/O input while its output feeds the GRP. The
programmable polarity Clock to the latch or register can
be connected to any I/O in the I/O-CLK/CLKEN set (one-
quarter of total I/Os) or to one of the dedicated clock input
pins (Y
to the register can be programmed to connect to any of
the I/O-CLK/CLKEN input pin set or to the global clock
enable inputs (CLKEN
inputs gives minimum clock-to-output delays and mini-
mizes delay variation with fanout. Combinatorial output
mode may be implemented by a dedicated architecture
bit and bypass MUX. I/O cell output polarity can be
programmed as active high or active low.
The ispGDXVA allows adjacent I/O cell MUXes to be
cascaded to form wider input MUXes (up to 16 x 1)
without incurring an additional full Tpd penalty. However,
there are certain dependencies on the locality of the
adjacent MUXes when used along with direct MUX
inputs.
Adjacent I/O Cells
Expansion inputs MUXOUT[n-2], MUXOUT[n-1],
MUXOUT[n+1], and MUXOUT[n+2] are fuse-selectable
for each I/O cell MUX. These expansion inputs share the
same path as the standard A, B, C and D MUX inputs, and
I/O MUX Operation
MUX Expander Using Adjacent I/O Cells
MUX1
0
0
1
1
x
). The programmable polarity Clock Enable input
MUX0
0
1
1
0
x
). Use of the dedicated clock
Data Input Selected
x
to MUX
M0
M1
M2
M3
x
allows the user to
4
allow adjacent I/O cell outputs to be directly connected
without passing through the global routing pool. The
relationship between the [N+i] adjacent cells and A, B, C
and D inputs will vary depending on where the I/O cell is
located on the physical die. The I/O cells can be grouped
into “normal” and “reflected” I/O cells or I/O “hemi-
spheres.” These are defined as:
Table 2 shows the relationship between adjacent I/O
cells as well as their relationship to direct MUX inputs.
Note that the MUX expansion is circular and that I/O cell
B30, for example, draws on I/Os B29 and B28, as well as
B31 and B32, even though they are in different hemi-
spheres of the physical die. Table 2 shows some typical
cases and all boundary cases. All other cells can be
extrapolated from the pattern shown in the table.
Figure 2. I/O Hemisphere Configuration of
ispGDX240VA
Direct and Expander Input Routing
Table 2 also illustrates the routing of MUX direct inputs
that are accessible when using adjacent I/O cells as
inputs. Take I/O cell D33 as an example, which is also
shown in Figure 3.
ispGDX80VA
ispGDX160V/VA
ispGDX240VA
Specifications ispGDX240VA
Device
D59
B0
B19-B0, A39-A20,
A19-A0, D39-D20
Normal I/O Cells
I/O cell 119 I/O cell 120
I/O cell 0
D30
B29
TBA
TBA
I/O cell 239
D29
B30
Reflected I/O Cells
B20-B39, C0-C19,
C20-C39, D0-D19
B59
D0
TBA
TBA