CS4205-KQR Cirrus Logic Inc, CS4205-KQR Datasheet - Page 59
![no-image](/images/manufacturer_photos/0/1/141/cirrus_logic_inc_sml.jpg)
CS4205-KQR
Manufacturer Part Number
CS4205-KQR
Description
Audio CODECs IC AC'97 Codec for Docking Stations
Manufacturer
Cirrus Logic Inc
Datasheet
1.CS4205-KQZ.pdf
(81 pages)
Specifications of CS4205-KQR
Number Of Adc Inputs
8
Number Of Dac Outputs
3
Conversion Rate
48 KSPs
Interface Type
Serial (5-Wire)
Resolution
18 bit, 20 bit
Maximum Operating Temperature
+ 70 C
Mounting Style
SMD/SMT
Package / Case
LQFP-48
Minimum Operating Temperature
0 C
Number Of Channels
1 ADC, 1 DAC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
10. POWER MANAGEMENT
10.1 AC ’97 Reset Modes
The CS4205 supports four reset methods, as de-
fined in the AC ’97 Specification: Cold Reset,
Warm Reset, New Warm Reset, and Register Reset.
A Cold Reset results in all AC ’97 logic (registers
included) initialized to its default state. A Warm
Reset or New Warm Reset leaves the contents of
the AC ’97 register set unaltered. A Register Reset
initializes only the AC ’97 registers to their default
states.
10.1.1 Cold Reset
A Cold Reset is achieved by asserting RESET# for
a minimum of 1 µs after the power supply rails
have stabilized. This is done in accordance with the
minimum timing specifications in the AC ’97 Seri-
al Port Timing section on page 10. Once de-assert-
ed, all of the CS4205 registers will be reset to their
default power-on states and the BIT_CLK and
SDATA_IN signals will be reactivated.
10.1.2 Warm Reset
A Warm Reset allows the AC-link to be reactivated
without losing information in the CS4205 registers.
A Warm Reset is required to resume from a D3
state where the AC-link had been halted yet full
power had been maintained. A primary codec
Warm Reset is initiated when the SYNC signal is
driven high for at least 1 µs and then driven low in
the absence of the BIT_CLK clock signal. The
BIT_CLK clock will not restart until at least 2 nor-
DS489PP4
hot
mal BIT_CLK clock periods (162.8 ns) after the
SYNC signal is de-asserted. A Warm Reset of the
secondary codec is recognized when the primary
codec on the AC-link resumes BIT_CLK genera-
tion. The CS4205 will wait for BIT_CLK to be sta-
ble to restore SDATA_IN activity, S/PDIF and/or
serial data port transmission on the following
frame.
10.1.3 New Warm Reset
The New Warm Reset also allows the AC-link to
be reactivated without losing information in the
registers. A New Warm Reset is required to resume
from a D3
removed. New Warm Reset is recognized by the
low-high transition of RESET# after the AC-link
has been programmed into PR4 powerdown. The
New Warm Reset functionality can be disabled by
setting the CRST bit in the Misc. Crystal Control
Register (Index 60h).
10.1.4 Register Reset
The last reset mode provides a Register Reset to the
CS4205. This is available only when the CS4205
AC-link is active and the Codec Ready bit is ‘set’.
The audio (including extended audio) control reg-
isters (Index 00h - 3Ah) and the vendor specific
registers (Index 5Ah - 7Ah) are reset to their de-
fault states by a write of any value to the Reset Reg-
ister (Index 00h). The modem (including GPIO)
registers (Index 3Ch - 56h) are reset to their default
states by a write of any value to the Extended Mo-
dem ID Register (Index 3Ch).
cold
state where AC-link power has been
CS4205
59