LTC4215CUFD Linear Technology, LTC4215CUFD Datasheet - Page 13
![no-image](/images/manufacturer_photos/0/3/388/linear_technology_sml.jpg)
LTC4215CUFD
Manufacturer Part Number
LTC4215CUFD
Description
IC,Power Control/Management,CMOS,LLCC,24PIN,PLASTIC
Manufacturer
Linear Technology
Datasheet
1.LTC4215CUFD.pdf
(28 pages)
Specifications of LTC4215CUFD
Linear Misc Type
Positive Low Voltage
Family Name
LTC4215
Package Type
QFN EP
Operating Supply Voltage (min)
2.9V
Operating Supply Voltage (max)
15V
Operating Temperature (min)
0C
Operating Temperature (max)
70C
Operating Temperature Classification
Commercial
Product Depth (mm)
4mm
Product Length (mm)
5mm
Mounting
Surface Mount
Pin Count
24
Lead Free Status / Rohs Status
Not Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTC4215CUFD
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC4215CUFD
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC4215CUFD#PBF
Manufacturer:
LT
Quantity:
4 500
Part Number:
LTC4215CUFD#PBF
Manufacturer:
LT凌特厂
Quantity:
20 000
Company:
Part Number:
LTC4215CUFD#TRPBF
Manufacturer:
LT
Quantity:
499
Company:
Part Number:
LTC4215CUFD#TRPBF
Manufacturer:
LT
Quantity:
6 000
Part Number:
LTC4215CUFD#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Company:
Part Number:
LTC4215CUFD-1
Manufacturer:
LT
Quantity:
10 000
Part Number:
LTC4215CUFD-1#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTC4215CUFD-2#PB
Manufacturer:
LINEAR/凌特
Quantity:
20 000
APPLICATIONS INFORMATION
dI/dt ramp stops and the inrush current follows the foldback
profi le as shown in Figure 2. The TIMER pin integrates at
100μA during start-up and once it reaches its threshold
of 1.235V, the part checks to see if it is in current limit,
which indicates that it has started up into a short-circuit
condition. If this is the case, the overcurrent fault bit, D2
in Table 5, is set and the part turns off. If the part is not in
current limit, the 25mV circuit breaker is armed and the
current limit is switched to 75mV. Alternately an internal
100ms start-up timer may be selected by tying the TIMER
pin to INTV
As the SOURCE voltage rises, the FB pin follows as set
by R7 and R8. Once FB crosses its 1.235V threshold, and
the start-up timer has expired, the GPIO pin, in its default
confi guration, ceases to pull low and indicates that power
is now good.
If R6 and C1 are employed for a constant current during
start-up, which produces a constant dV/dt at the output,
a 20μA pull-up current from the gate pin slews the gate
upwards and the part is not in current limit. The start-up
TIMER may expire in this condition and an OC fault is not
generated even though start-up has not completed. Either
the sense voltage increases to the 25mV CB threshold and
V
DD
V
25mV
10mV
SENSE
+ 6V
V
DD
CC
LIMITED
SS
.
Figure 2. Power-Up Waveforms
t
STARTUP
LIMITED
FB
EXPIRES
TIMER
4215 F02
V
V
GPIO1
(POWER GOOD)
I
LOAD
GATE
OUT
• R
SENSE
generates an OC fault, or the FB pin voltage crosses its
1.235V power good threshold and the GPIO pin signals
power good.
GATE Pin Voltage
A curve of GATE-to-SOURCE drive vs V
Typical Performance Characteristics. At minimum input
supply voltage of 2.9V, the minimum GATE-to-SOURCE
drive voltage is 4.7V. The GATE-to-SOURCE voltage is
clamped below 6.5V to protect the gates of logic level
N-channel MOSFETs.
Turn-Off Sequence
The GATE is turned off by a variety of conditions. A normal
turn-off is initiated by the ON pin going low or a serial bus
turn-off command. Additionally, several fault conditions
turn off the GATE. These include an input overvoltage
(OV pin), input undervoltage (UV pin), overcurrent circuit
breaker (SENSE
a logic one into the UV, OV or OC fault bits (D0-D2 in
Table 5) also latches off the GATE if their auto-retry bits
are set to false.
Normally the MOSFET is turned off with a 1mA current
pulling down the GATE pin to ground. With the MOSFET
turned off, the SOURCE and FB voltages drop as C
charges. When the FB voltage crosses below its threshold,
GPIO pulls low to indicate that the output power is no
longer good.
If the V
INTV
down of the MOSFET is initiated. The GATE pin is pulled
down with a 450mA current to the SOURCE pin.
Overcurrent Fault
The LTC4215 features an adjustable current limit that
protects against short circuits or excessive load current.
An overcurrent fault occurs when the circuit breaker 25mV
threshold has been exceeded for longer than the 20μs
(LTC4215) or 420μs (LTC4215-2) time-out delay. Current
limiting begins immediately when the current sense voltage
between the V
CC
DD
drops below 2.60V for greater than 1μs, a fast shut
pin falls below 2.74V for greater than 2μs or
DD
–
LTC4215/LTC4215-2
and SENSE pins reaches 75mV. The GATE
pin), or EN transitioning high. Writing
DD
is shown in the
13
L
4215fe
dis-