LT1952IGN Linear Technology, LT1952IGN Datasheet - Page 19

• Manufacturer Part Number: LT1952IGN
• Description: IC,SMPS CONTROLLER,CURRENT-MODE,SOP,16PIN,PLASTIC
• Manufacturer: Linear Technology

APPLICATIO S I FOR ATIO
This gives k = 1 and t
Re-arranging the above equation to solve for SS_MAXDC
= V
Step 3: Calculate t(V
Recall the time for SS_MAXDC to charge to a given voltage
V
(Figure 11 gives the model for SS_MAXDC charging)
The rise time for the converter output
Example (3) Time For Maximum Duty Cycle Clamp to
Reach Within X% of Target Value
A maximum duty cycle clamp of 72% was calculated
previously in the section ‘Programming Maximum Duty
Cycle Clamp’. The programmed value used for
SS_MAXDC(DC) was 1.84V.
The time for SS_MAXDC to charge from its minimum
value V
by,
SS
0.6 = k • 0.522(SS_MAXDC(DC)/SD_V
(t
For SD_V
= [0.6 + (t
= [0.6 + (40ns • 200kHz)(1.32V)]/(1 • 0.522)
= (0.608)(1.32)/0.522 = 1.537V
t = R
For R
For C
= t(V
= 2.63e
t(V
ln(1 – 1.66/1.84) = 2.63e
= 5e
= t(V
= 3.5e
= t[(1 – (X/100) • SS_MAXDC(DC)] – t(V
t(0.45) = t(1.803) – t(0.45)
t(SS_MAXDC charge time within X% of target)
For X = 2 and V
SS(REG)
DELAY
is given by,
SS(REG)
–3
CHARGE
SS(MIN)
SS(0.8V)
SS(REG)
SS
T
–3
s
= 35.7k, R
–3
• f
= 0.1µF, this gives t(V
s
SEC
OSC
DELAY
• (–1) • ln(0.565) = 1.5e
) = t(V
) – t(V
• C
) = 2.63e
to within X% of SS_MAXDC(DC) is given
= 1.32V, f
)
SS
SS(MIN)
• f
U
SS(1.537V)
B
SS(REG)
• (–1) • ln(1 – V
OSC
SS(ACTIVE)
DELAY
= 100k, R
4
)(SD_V
OSC
U
• 1e
= 0.45V, t(0.98 • 1.84) –
) – t(V
= 40ns.
–3
) = 26.3k • 0.1µF • –1 •
= 200kHz and R
–7
• (–1) • ln(0.146)
) = (5 – 1.5)e
CHARGE
SEC
• (–1) • ln(1 – 0.8/1.84)
SS(ACTIVE)
SS(ACTIVE)
W
)]/(k • 0.522)
SS
–3
/SS_MAXDC(DC))
= 26.3k
s
SEC
)
)
SS(MIN)
–3
) –
DELAY
U
s
)
= 40k
From previous calculations, t(0.45) = 7.3e – 4 s.
Using previous values for R
Hence the time for SS_MAXDC to charge from its mini-
mum reset threshold of 0.45V to within 2% of its target
value is given by,
Forward Converter Applications
The following section covers applications where the
LT1952/LT1952-1 are used in conjunction with other LTC
parts to provide highly efficient power converters using
the single switch forward converter topology.
95% Efficient, 5V, Synchronous Forward Converter
The circuit in Figure 14 is based on the LT1952-1 to
provide the simplest forward power converter circuit —
using only one primary MOSFET. The SOUT pin of the
LT1952-1 provides a synchronous control signal for the
LTC1698 located on the secondary. The LTC1698 drives
secondary side synchronous rectifier MOSFETs to achieve
high efficiency. The LTC1698 also serves as an error
amplifier and optocoupler driver.
Efficiency and transient response are shown in Figures 12
and 13. Peak efficiencies of 95% and ultra-fast transient
response are superior to presently available power mod-
ules. Integrated soft-start, over-current detection and
short circuit hiccup mode provide low stress, reliable
protection. In addition, the circuit in Figure 14 is an all-
ceramic capacitor solution providing low output ripple
voltage and improved reliability. The LT1952-based con-
verter can be used to replace power module converters at
a much lower cost. The LT1952 solution benefits from
thermal conduction of the system board resulting in
higher efficiencies and lower rise in component tempera-
tures. The 7mm height allows dense packaging and the
circuit can easily be adjusted to provide an output voltage
from 1.23V to 26V. Higher currents are achievable by
simple scaling of power components. The LT1952-1
-based solution in Figure 14 is a powerful topology for
replacement of a wide range of power modules.
t(1.803) = 2.63e
= 2.63e
t(1.803) – t(0.45) =
1.03e
–2
–3
– 7.3e
• (–1) • ln(0.02) = 1.03e
–4
–4
= 9.57e
• 1e
LT1952/LT1952-1
–7
–3
T
• (–1) • ln(1 – 1.803/1.84)
, R
B
, and C
–2
s
SS
,
19
19521fb