N50P111 austriamicrosystems, N50P111 Datasheet
N50P111
Specifications of N50P111
Related parts for N50P111
N50P111 Summary of contents
Page 1
... High-speed I²C interface Configurable interrupt output for motion detection Push button feature 3 Applications The EasyPoint™ N50P111 is ideal for small form-factor manual input devices in battery operated equipment, such as Mobile phones, MP3 players, PDAs, GPS receivers, Gaming consoles and Analog joystick replacement. ...
Page 2
... Electrical Characteristics........................................................................................................................................................... 7.1 Operating Conditions............................................................................................................................................................................ 6 7.2 Digital IO Pads DC/AC Characteristics................................................................................................................................................. 6 7.3 Switch Characteristics .......................................................................................................................................................................... 7 7.4 Mechanical Specifications .................................................................................................................................................................... 8 7.5 Recommended Reflow Temperature Profile......................................................................................................................................... 8 8 Using the N50P111 Module ...................................................................................................................................................... 8.1 Powering up the Module....................................................................................................................................................................... 9 8.2 Registers Initialization........................................................................................................................................................................... 9 8.3 C Source Code Example .................................................................................................................................................................... 10 8.3.1 Initialization ................................................................................................................................................................................ 10 8.3.2 Offset Calibration ....................................................................................................................................................................... 10 8 ...
Page 3
... TM EasyPoint N50P111 Datasheet - 11.6 Yp Register (14h).............................................................................................................................................................................. 26 11.7 Yn Register (15h).............................................................................................................................................................................. 26 11.8 M_ctrl Register (2Bh)........................................................................................................................................................................ 26 11.9 J_ctrl Register (2Ch)......................................................................................................................................................................... 27 11.10 T_ctrl Register (2Dh) ...................................................................................................................................................................... 27 11.11 Control Register 2 (2Eh) ................................................................................................................................................................. 27 11.12 Registers Table ............................................................................................................................................................................... 28 12 Package Drawings and Markings ......................................................................................................................................... www.austriamicrosystems.com/N50P111 Revision 1 ...
Page 4
... TM EasyPoint N50P111 Datasheet - Pin Assignments Figure 3. N50P111-xxxxx-H Schematics U1 14 ModeOTP VDD 16 PDIO VDDp 15 PCLK VSS 5 tb0 6 tb1 RESET 7 tb2 8 tb3 SCL 9 Test_Coil SDA 17 EPAD ADDR GND S1 1 GND Dome_Switch 5.1 Pin Descriptions Table 1. Pin Descriptions Connector Pin # Pin Type 1 Power 2 Power ...
Page 5
... Peripheral supply voltage VDDp Input pin voltage Input current (latchup immunity) SCR Electrostatic discharge ESD T Storage temperature Strg Humidity non-condensing Degrees of protection www.austriamicrosystems.com/N50P111 Electrical Characteristics on page 6 is not implied. Exposure to absolute Min Max Units -0 -0.3 V SCL, SDA, RESETn, ADDR VDD + 0.3 -0.3 VDDp + 0 ...
Page 6
... Input leakage current LEAK Inputs: ADDR, RESETn (JEDEC76) V High level input voltage IH V Low level input voltage IL I Input leakage current LEAK Outputs: SDA V High level output voltage OH www.austriamicrosystems.com/N50P111 Min Typ Max Units 2.7 3.6 V 1.7 VDD V 3+3760/ts [ms] µA 10+3760/ts [ms] 3 µA ...
Page 7
... High level output voltage OH V Low level output voltage OL C Capacitive load L 7.3 Switch Characteristics Table 5. Switch Characteristics Parameter Contact resistance of dome switch Dielectric withstanding voltage Insulation resistance Bouncing (On/Off) www.austriamicrosystems.com/N50P111 Min Max Units VSS + 0.4 V VDDP * 0.2 V VSS + 0.4 V VDDP * 0.2 V 400 pF 400 ...
Page 8
... Shaft strength (XYZ direction) Free fall Over force 7.5 Recommended Reflow Temperature Profile Figure 4. Reflow Temperature Profile 250 ~ 260°C 217ºC 170ºC 140ºC www.austriamicrosystems.com/N50P111 Note Single shaft LCP LCP & PA46 Stainless Steel or Copper alloy ±2.00mm (±10%) 0.22mm (±0.05mm) 0.70N (±0.15N) 1.80N (± ...
Page 9
... Using the N50P111 Module 8.1 Powering up the Module The N50P111 module has a Power ON Reset (POR) cell to monitor the VDD voltage at startup and reset all the internal registers. After the internal reset is completed, the POR cell is disabled in order to save current during normal operation. ...
Page 10
... I2C_Read8(0x40, 0x10); // Read X position y_cal += (signed char) I2C_Read8(0x40, 0x11); // Read Y position } // offset_X and offset_Y are global variables, used for each coordinate readout in the interrupt routine offset_X = -(x_cal>>4); // Average X: divide by 16 offset_Y = -(y_cal>>4); // Average Y: divide Enable the MCU interrupts } www.austriamicrosystems.com/N50P111 Revision 1 ...
Page 11
... Y_temp = y_reg + offset_Y; /* OPTIONAL: If X_temp and Y_temp are near the center since a few interrupts, meaning the knob has been released, the module can be put back in a slow power mode (e.g. Wakeup mode INT_function=1 with 320ms rate Enable the MCU interrupts } www.austriamicrosystems.com/N50P111 Revision 1 ...
Page 12
... X = 1.0mm → X register = - 2.0mm → X register = -128 → Y register = 0mm → Y register = 0mm X_Reg < Xn → Int = 0 (active) X_Reg < Xn → Int = 0 (active) (see I²C Registers on page 23) 8.2 and 8.3 or refer to the austriamicrosystems N50P111 encoder application notes: Revision 1 have been set by the user ...
Page 13
... Those values are in an ideal condition, where the knob takes place over the center position of the N50P111 sensor once released. The zero position may vary between two N50 modules, and an offset must be applied to X and Y in order to compensate the X,Y coordinates to 0,0 once the knob is released. More information can be found in chapters Figure 7. X Register / X Displacement (Y=0µ ...
Page 14
... START-UP. After power up and after applying a soft reset (Reg 0Fh [1]) or hardware reset (RESETn input, LOW pulse >100ns), N50P111 enters the START- UP state. During this state the internal registers are loaded with their reset values. Then the N50P111 will perform one measurement and switches automatically into the WAIT state ...
Page 15
... The N50P111 supports the 2-wire high-speed I²C protocol in device mode, according to the NXP specification UM10204. The host MCU (master) has to initiate the data transfers. The 7-bit device address of the N50P111 depends on the state at the pin ADDR. ADDR = 0 → Slave address =‘1000 000’ (40h) ADDR = 1 → ...
Page 16
... I/O Capacitance (SDA, SCL) I/O 1. Maximum V = VDDpmax +0.5V or 5.5V, which ever is lower For capacitive bus loads between 100pF and 400pF, the timing parameters must be linearly interpolated. www.austriamicrosystems.com/N50P111 Condition VDDp < 2V VDDp < 2V SCLH output levels between 0.3VDDp and 0.7VDDp Input Voltage between ...
Page 17
... A fast-mode device can be used in standard-mode system, but the requirement t the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line t www.austriamicrosystems.com/N50P111 HS-mode C FS-mode ...
Page 18
... I²C Modes The N50P111 supports the I²C bus protocol. A device that sends data onto the bus is defined as a transmitter and a device receiving data as a receiver. The device that controls the message is called a master. The devices that are controlled by the master are referred to as slaves. A master device that generates the serial clock (SCL), controls the bus access, and generates the START and STOP conditions must control the bus. The N50P111 operates as a slave on the I² ...
Page 19
... SDA. After the N50P111 acknowledges the slave address + write bit, the master transmits a register address to the N50P111. This sets the address pointer on the N50P111. If the address is a valid readable address the N50P111 answers by sending an acknowledge. If the address-pointer points to an invalid position a “not acknowledge” is sent. The master may then transmit zero or more bytes of data ...
Page 20
... Slave Transmitter Mode (Read Mode): The first byte is received and handled as in the slave receiver mode. However, in this mode, the direction bit indicates that the transfer direction is reversed. Serial data is transmitted on SDA by the N50P111 while the serial clock is input on SCL. START and STOP conditions are recognized as the beginning and end of a serial transfer. The slave address byte is the first byte received after the master generates a START condition ...
Page 21
... Datasheet - I ² 10.4.5 High Speed Mode The N50P111 is capable to work in HS-mode. For switching to HS-mode the Master has to send the sequence: START, MASTER CODE, NACK. This sequence is sent in FS-mode device is allowed to acknowledge the master code, the master code is followed by a not-acknowledge. After a device receives the master code it has to switch from FS-settings to HS-settings within t receive a STOP command ...
Page 22
... Sequential read over the whole address range is possible including address overflow. Writing: A write to a wrong address is not acknowledged by the N50P111 slave, although the address pointer is increased. When the address pointer points to a valid address again, a successful write accessed is acknowledged. Page write over the whole address range is possible including address overflow ...
Page 23
... Soft_rst bit goes back to 0 once the internal reset sequence is finished Conversion of new coordinates ongoing, no valid coordinate is present in the X and Y_res_int registers. Reading those registers at that moment can give wrong values New coordinate values are ready in X and Y_res_int registers. www.austriamicrosystems.com/N50P111 Bit 4 Bit 3 Bit 2 INT_disable ...
Page 24
... Note: The values in Control Register 1, X_register and Y_res_int register are frozen when the I²C address pointer is set to 0Fh, 10h or 11h. This ensures that the Data_valid bit, X and Y values are taken at the same time. In order to get updated values from those registers, set the address pointer to any other address. www.austriamicrosystems.com/N50P111 ∆t timebase ...
Page 25
... R/W R/W R/W Reset value: 1111 1011 (-5d) Bit Xn range value, Two’s complement (signed: -128 ~ +127). 7:0 Determines the RIGHT threshold for the activation of INTn output (if output enabled), when bit INT_function = 1 Control Register 1 (0Fh) on page www.austriamicrosystems.com/N50P111 Bit 4 Bit 3 X[4] X[ Bit Description ...
Page 26
... Bit 5 M_ctrl[7] M_ctrl[6] M_ctrl[5] R/W R/W R/W Reset value: 0000 0000 (00h) Bit Middle hall element control register. 7:0 The M_ctrl register must be set to 00h after power up for N50P111 module. www.austriamicrosystems.com/N50P111 Bit 4 Bit 3 Yp[4] Yp[3] R/W R/W Bit Description 23). Bit 4 Bit 3 ...
Page 27
... Bit Scaling control register. This register controls the scaling factor of the XY coordinates to fit to the 8-bit X and Y register (full dynamic range). 7:0 The T_ctrl register must be set to 16h (default value) after power up for N50P111 module. 11.11 Control Register 2 (2Eh) Bit 7 Bit 6 Bit 5 ...
Page 28
... R/W c4_neg <11:8> c4_neg <7:0> c4_pos <11:8> c4_pos <7:0> www.austriamicrosystems.com/N50P111 Reset Format Bit Value IC Identification 8 bit Manufacture ID Code 0C 0Ch <7:0> 8 bit Component ID Version 0D 0Dh <7:4> 8 bit Silicon Revision 0E 00h <7:0> Control_register_1 1 : Idle mode 0Fh 1b <7> Low Power mode Low Power readout time base register ...
Page 29
... For N50P111, configure to 00h (default) Attenuation of the outer Hall elements 2Ch 06h <7:0> For N50P111, configure to 06h (default) Scaling factor of XY coordinates 2Dh 09h <7:0> For N50P111, configure to 16h (default) Control_register_2 2Eh 1b <7> Test only, must be ‘1’ Test only, must be ‘0’ 2Eh 0b <6> ...
Page 30
... TM EasyPoint N50P111 Datasheet - Package Drawings and Markings Figure 18. N50P111 Dimensions (mm ±0.15) Figure 19. Recommended PCB Layout (mm ±0.05) www.austriamicrosystems.com/N50P111 Revision 1 ...
Page 31
... TM EasyPoint N50P111 Datasheet - Figure 20. Recommended on Casing Design & Mounting Note www.austriamicrosystems.com/N50P111 Revision 1 ...
Page 32
... AG Tobelbaderstrasse 30 A-8141 Unterpremstaetten, Austria Tel: +43 (0) 3136 500 0 Fax: +43 (0) 3136 525 01 For Sales Offices, Distributors and Representatives, please visit: http://www.austriamicrosystems.com/contact www.austriamicrosystems.com/N50P111 Owner jlu Updated Applications on page 1 Updated sections 8.3.1, 10, 10.2, 10.3, 11.1, 11.3, 11.10, 11.11, Revision 1.1 Description ...