TDA5210T Infineon Technologies, TDA5210T Datasheet - Page 27
![IC ASK/FSK RECEIVER P-TSSOP-28](/photos/14/17/141745/448-28-tssop-1_sml.jpg)
TDA5210T
Manufacturer Part Number
TDA5210T
Description
IC ASK/FSK RECEIVER P-TSSOP-28
Manufacturer
Infineon Technologies
Datasheet
1.TDA5210.pdf
(53 pages)
Specifications of TDA5210T
Frequency
810MHz ~ 870MHz, 400MHz ~ 440MHz
Sensitivity
-107dBm
Modulation Or Protocol
ASK, FSK
Applications
Alarm Systems, Communication Systems
Current - Receiving
4.8mA
Data Interface
PCB, Surface Mount
Antenna Connector
PCB, Surface Mount
Voltage - Supply
4.6 V ~ 5.5 V
Operating Temperature
-40°C ~ 105°C
Package / Case
28-TSSOP
Operating Temperature (min)
-40C
Operating Temperature Classification
Automotive
Product Depth (mm)
4.4mm
Product Length (mm)
9.7mm
Operating Supply Voltage (min)
4.5V
Operating Supply Voltage (typ)
5V
Operating Supply Voltage (max)
5.5V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
SP000087156
Wireless Components
4.4 Quartz Frequency Calculation
As described in Section 3.4.3 the operating range of the on-chip VCO is 820 to
860 MHz with a nominal center frequency of 840MHz. This signal is divided by
2 before applied to the mixer in case of operation at 434 MHz. This local oscil-
lator signal can be used to downconvert the RF signals both with high- or low-
side injection at the mixer. The resulting receive frequency ranges then extend
between 810 and 870MHz or between 400 and 440MHz. Low-side injection of
the local oscillator has to be used for receive frequencies between 840 and
870MHz as well as high-side injection for receive frequencies below 840MHz.
Corresponding to that in the 400MHz region low-side injection is applicable for
receive frequencies above 420MHz, high-side injection below this frequency.
Therefore for operation both in the 868 and the 434 MHz ISM bands low-side
injection of the local oscillator has to be used. Then the local oscillator fre-
quency is calculated by subtracting the IF frequency (10.7 MHz) from the RF
frequency (434 or 868 MHz). Please note that no sign-inversion occurs in case
of reception and demodulation of FSK-modulated signals.
The overall division ratios in the PLL are 64 or 128 in case of operation at
868 MHz or 32 and 64 in case of operation at 434 MHz, depending on the crys-
tal frequency used as shown below. The quartz frequency in case of low-side
injection may be calculated by using the following formula:
with
:
Table 4-1 Dependence of PLL Overall Division Ratio on FSEL and CSEL
FSEL
open
open
GND
GND
ƒ
ƒ
ƒ
ƒ
r
QU
RF
LO
QU
= (ƒ
f
f
f
f
QU
QU
QU
QU
receive frequency
local oscillator (PLL) frequency (ƒ
quartz oscillator frequency
ratio of local oscillator (PLL) frequency and quartz frequency as
shown in the subsequent table
RF
-
868
434
868
434
10.7) / r
4 .
2 .
4 - 6
4 .
2 .
MHz
MHz
MHz
MHz
10
10
10
10
7 .
7 .
7 .
CSEL
open
GND
open
GND
7 .
MHz
MHz
MHz
MHz
/
/
64
/
32
/
128
RF
64
-
10.7)
13
13
6.6172
.
. 6
.
40156
23437
7008
Specification, May 2001
Ratio r = (f
MHz
MHz
MHz
MHz
128
64
32
64
Applications
TDA 5210
LO
/f
QU
)