ADAU1961WBCPZ Analog Devices Inc, ADAU1961WBCPZ Datasheet - Page 37

• Manufacturer Part Number: ADAU1961WBCPZ
• Description: IC STEREO AUD CODEC LP 32LFCSP
• Manufacturer: Analog Devices Inc
• Type: Audio Codecr

Specifications of ADAU1961WBCPZ

• Data Interface: Serial
• Resolution (bits): 24 b
• Number Of Adcs / Dacs: 2 / 2
• Sigma Delta: No
• S/n Ratio, Adcs / Dacs (db) Typ: 99 / 101
• Dynamic Range, Adcs / Dacs (db) Typ: 99 / 101
• Voltage - Supply, Analog: 2.97 V ~ 3.63 V
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 32-VFQFN, CSP Exposed Pad
• Audio Codec Type: Stereo
• No. Of Adcs: 2
• No. Of Dacs: 2
• No. Of Input Channels: 2
• No. Of Output Channels: 2
• Adc / Dac Resolution: 24bit
• Adcs / Dacs Signal To Noise Ratio: 101dB
• Sampling Rate: 96kSPS
• No. Of: RoHS Compliant
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The R/ W bit determines the direction of the data. A Logic 0 on
the LSB of the first byte means that the master will write infor-
mation to the peripheral, whereas a Logic 1 means that the
master will read information from the peripheral after writing
the subaddress and repeating the start address. A data transfer
takes place until a stop condition is encountered. A stop
condition occurs when SDA transitions from low to high while
SCL is held high.
and
Stop and start conditions can be detected at any stage during the
data transfer. If these conditions are asserted out of sequence with
normal read and write operations, the ADAU1961 immediately
jumps to the idle condition. During a given SCL high period,
(CONTINUED)
(CONTINUED)
(CONTINUED)
(CONTINUED)
Figure 49
START BY
(CONTINUED)
(CONTINUED)
MASTER
SDA
SCL
START BY
SDA
SCL
MASTER
SDA
SCL
SDA
SDA
SCL
SCL
shows an I
Figure 48
0
0
1
2
C read.
shows the timing of an I
1
1
SUBADDRESS BYTE 2
CHIP ADDRESS BYTE
READ DATA BYTE 1
1
1
CHIP ADDRESS BYTE
FRAME 1
FRAME 3
FRAME 5
SUBADDRESS BYTE 2
1
FRAME 1
0
FRAME 3
ADDR1
0
ADDR1
ADDR0
Figure 49. I
Figure 48. I
2
C write,
ADDR0
R/W
ADAU1961
2
ADAU1961
MASTER
C Read from ADAU1961 Clocking
ACK BY
2
Rev. 0 | Page 37 of 76
ACK BY
C Write to ADAU1961 Clocking
R/W
ACK BY
ADAU1961
ADAU1961
ACK BY
ACK BY
STOP BY
MASTER
REPEATED
START BY MASTER
the user should only issue one start condition, one stop condition,
or a single stop condition followed by a single start condition. If
an invalid subaddress is issued by the user, the ADAU1961 does
not issue an acknowledge and returns to the idle condition.
If the user exceeds the highest subaddress while in autoincrement
mode, one of two actions is taken. In read mode, the ADAU1961
outputs the highest subaddress register contents until the master
device issues a no acknowledge, indicating the end of a read. A
no acknowledge condition is where the SDA line is not pulled
low on the ninth clock pulse on SCL. If the highest subaddress
location is reached while in write mode, the data for the invalid
byte is not loaded into any subaddress register, a no acknowledge
is issued by the ADAU1961, and the part returns to the idle
condition.
0
SUBADDRESS BYTE 1
1
FRAME 2
CHIP ADDRESS BYTE
SUBADDRESS BYTE 1
DATA BYTE 1
1
FRAME 4
FRAME 4
FRAME 2
1
0
ADDR1
ADAU1961
ADDR0
ACK BY
ADAU1961
ADAU1961
ACK BY
ACK BY
R/W
ADAU1961
ACK BY
ADAU1961
STOP BY
MASTER