MM908E625ACDWB Freescale Semiconductor, MM908E625ACDWB Datasheet - Page 25

• Manufacturer Part Number: MM908E625ACDWB
• Description: IC QUAD HALF BRDG MCU/LIN 54SOIC
• Manufacturer: Freescale Semiconductor

Specifications of MM908E625ACDWB

• Applications: Automotive Mirror Control
• Core Processor: HC08
• Program Memory Type: FLASH (16 kB)
• Controller Series: 908E
• Ram Size: 512 x 8
• Interface: SCI, SPI
• Number Of I /o: 13
• Voltage - Supply: 8 V ~ 18 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 54-SOIC (0.300", 7.50mm Width) Exposed Pad
• Program Memory Size: 16 KB
• Number Of Programmable I/os: 54
• Number Of Timers: 16
• Operating Supply Voltage: - 18 V to + 28 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

ANALOG DIE I/OS
LIN Physical Layer
communication in automotive applications. The LIN physical
layer is designed to meet the LIN physical layer specification.
limitation and thermal shutdown. An internal pull-up resistor
with a serial diode structure is integrated, so no external pull-
up components are required for the application in a slave
node. The fall time from dominant to recessive and the rise
time from recessive to dominant is controlled. The symmetry
between both slew rate controls is guaranteed.
external disturbance, guaranteeing communication during
external disturbance.
PSON bit in the System Control Register (SYSCTL). If the
transmitter works in the current limitation region, the LINCL
bit in the System Status Register (SYSSTAT) is set. Due to
excessive power dissipation in the transmitter, software is
advised to monitor this bit and turn the transmitter off
immediately.
TXD PIN
LIN transmitter (see
is low (dominant state). When TXD is HIGH, the LIN output
MOSFET is turned off. The TXD pin has an internal pull-up
current source in order to set the LIN bus in recessive state
in the event, for instance, the microcontroller could not control
it during system power-up or power-down.
RXD PIN
reports the state of the LIN bus voltage. LIN HIGH (recessive
state) is reported by a high level on RXD, LIN LOW (dominant
state) by a low level on RXD.
STOP MODE/WAKE-UP FEATURE
physical layer is disabled. The receiver pin is still active and
able to detect wake-up events on the LIN bus line.
Register is set), a falling edge on the LIN line causes an
interrupt. This interrupt switches on the main voltage
regulator and generates a system wake-up.
Analog Integrated Circuit Device Data
Freescale Semiconductor
The LIN bus pin provides a physical layer for single-wire
The LIN driver is a low-side MOSFET with internal current
The LIN pin offers high susceptibility immunity level from
The LIN transmitter circuitry is enabled by setting the
The TXD pin is the MCU interface to control the state of the
The RXD transceiver pin is the MCU interface, which
During STOP mode operation the transmitter of the
If LIN interrupt is enabled (LINIE bit in the Interrupt Mask
Figure
1). When TXD is LOW, LIN output
Analog Multiplexer/ADOUT Pin
of the MCU. See
read seven internal diagnostic analog voltages.
Current Recopy
current sense circuits of the half-bridges. These sense
circuits offer a voltage proportional to the current through the
low-side MOSFET. High or low resolution is selectable:
5.0 V/2.5 A or 5.0 V/500 mA, respectively. Refer to
Bridge Current Recopy on page
Analog Input PA1
multiplexer, permitting analog values from the periphery to be
read.
TEMPERATURE SENSOR
This sensor offers a voltage that is proportional to the actual
chip junction temperature.
V
of the external supply voltage. The output of this voltage is
V
selected with the ADMUX Register.
ANALOG MULTIPLEXER CONFIGURATION
REGISTER (ADMUX)
SS3, SS2, SS1, and SS0—A/D Input Select Bits
microcontroller according to
SS1, and SS0 bits.
Reset
Read
Write
SUP
SUP
Bits
The ADOUT pin is the analog output interface to the ADC
The analog multiplexer is connected to the four low-side
The analog input PA1 is directly connected to the analog
The 908E625 includes an on-chip temperature sensor.
The V
The different internal diagnostic analog voltages can be
These read/write bits select the input to the ADC in the
/RATIO
PRESCALER
SUP
7
0
0
Register Name and Address: ADMUX - $07
VSUP
prescaler permits the reading or measurement
6
0
0
Figure
.
5
0
0
LOGIC COMMANDS AND REGISTERS
12. An analog multiplexer is used to
FUNCTIONAL DEVICE OPERATION
Table
4
0
0
34.)
7. Reset clears SS3, SS2,
SS3
3
0
SS2
2
0
SS1
1
0
Half-
908E625
SS0
0
0
25