KSZ8842-PMQLI Micrel Inc, KSZ8842-PMQLI Datasheet - Page 29
![2-Port Ethernet Switch/Repeater + 32-bit/33MHz PCI Bus Interface, Ind Temp ( )](/photos/6/81/68152/576-128-pqfp_sml.jpg)
KSZ8842-PMQLI
Manufacturer Part Number
KSZ8842-PMQLI
Description
2-Port Ethernet Switch/Repeater + 32-bit/33MHz PCI Bus Interface, Ind Temp ( )
Manufacturer
Micrel Inc
Specifications of KSZ8842-PMQLI
Controller Type
Ethernet Switch Controller
Interface
PCI
Voltage - Supply
3.1 V ~ 3.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
128-MQFP, 128-PQFP
Number Of Primary Switch Ports
2
Internal Memory Buffer Size
32
Operating Supply Voltage (typ)
3.3V
Fiber Support
Yes
Integrated Led Drivers
Yes
Phy/transceiver Interface
MII
Power Supply Type
Analog/Digital
Package Type
PQFP
Data Rate (typ)
10/100Mbps
Vlan Support
Yes
Operating Temperature (max)
85C
Operating Temperature (min)
-40C
Pin Count
128
Mounting
Surface Mount
Jtag Support
No
Operating Supply Voltage (max)
3.5V
Operating Supply Voltage (min)
3.1V
Operating Temperature Classification
Industrial
Data Rate
100Mbps
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
576-1636 - BOARD EVALUATION KSZ8842-PMQL
Current - Supply
-
Lead Free Status / RoHS Status
Compliant, Lead free / RoHS Compliant
Other names
576-2121
KSZ8842-PMQLI
KSZ8842-PMQLI
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
KSZ8842-PMQLI
Manufacturer:
TI
Quantity:
3 100
Micrel, Inc.
Broadcast Storm Protection
The KSZ8842-PMQL/PMBL has an intelligent option to protect the switch system from receiving too many broadcast
packets. As the broadcast packets are forwarded to all ports except the source port, an excessive number of switch
resources (bandwidth and available space in transmit queues) may be utilized. The KSZ8842-PMQL/PMBL has the
option to include “multicast packets” for storm control. The broadcast storm rate parameters are programmed globally,
and can be enabled or disabled on a per port basis in P1CR1[7] and P2CR1[7]. The rate is based on a 67ms interval
for 100Base-T and a 670ms interval for 10Base-T. At the beginning of each interval, the counter is cleared to zero and
the rate limit mechanism starts to count the number of bytes during the interval. The rate definition is described in
SGCR3[15:18]. The default setting is 0x63 (99 decimal). This is equal to a rate of 1% minimum size packets, calculated
as follows:
Where 148,800 frames/sec is based on 64-byte blocks of 100Base-T packets with 12 bytes of IPG and 8 bytes of
preamble between packets.
Repeater Mode
When KSZ8842-PMQL/PMBL is set to repeater mode (SGCR3[7] = 1), it only works on 100BT half-duplex mode. In
repeater enabled mode, all ingress packets will broadcast to other two ports without MAC check and learning. Before
setting the device to repeater mode, the user has to set bit 13 (100Mbps), bit 12 (auto-negotiation disabled) and bit 8
(half duplex) in both P1MBCR and P2MBCR registers as well as to set bit 6 (host half duplex) in SGCR3 register for
repeater mode.
The latency in repeater mode is defined from the 1st bit of DA into the ingress port 1 to the 1st bit of DA out of the
egress port 2. The minimum is 270 ns and the maximum is 310 ns (one clock skew of 25 MHz between TX and RX).
Clock Generator
The X1 and X2 pin/balls are connected to a 25MHz crystal. X1 can also serve as the connector to a 3.3V, 25MHz
oscillator (as described in the pin/ball description). The PCI Bus Interface supports a maximum speed of 33MHz PCLK
(PCI Bus Clock).
Advanced Switch Functions
Spanning Tree Support
To support spanning tree, the host port is the designated port for the processor.
The other ports can be configured in one of the five spanning tree states via “transmit enable”, “receive enable” and
“learning disable” register settings in registers P1CR2 and P2CR2 for ports 1 and 2, respectively. Table 4 shows the
port setting and software actions taken for each of the five spanning tree states.
October 2007
Disable State
The port should
not forward or
receive any
packets. Learning
is disabled.
Blocking State
Only packets to
the processor are
forwarded.
Listening State
Only packets to
and from the
processor are
148,800 frames/sec X 67 ms/interval X 1% = 99 frames/interval (approx.) = 0x63
Port Setting
“transmit enable = 0,
receive enable = 0,
learning disable = 1”
Port Setting
“transmit enable = 0,
receive enable = 0,
learning disable = 1”
Port Setting
“transmit enable = 0,
receive enable = 0,
learning disable = 1”
Software Action
The processor should not send any packets to the port. The switch
may still send specific packets to the processor (packets that
match some entries in the “static MAC table” with “overriding bit”
set) and the processor should discard those packets. Address
learning is disabled on the port in this state.
The processor should not send any packets to the port(s) in this
state. The processor should program the “Static MAC table” with
the entries that it needs to receive (for example, BPDU packets).
The “overriding” bit should also be set so that the switch will
forward those specific packets to the processor. Address learning
is disabled on the port in this state.
Software Action
The processor should program the “Static MAC table” with the
entries that it needs to receive (for example, BPDU packets). The
“overriding” bit should be set so that the switch will forward those
Software Action
29
KSZ8842-PMQL/PMBL
M9999-100207-1.5