ADF4360-6BCPZ Analog Devices Inc, ADF4360-6BCPZ Datasheet - Page 16

• Manufacturer Part Number: ADF4360-6BCPZ
• Description: IC,FREQUENCY SYNTHESIZER,BICMOS,LLCC,24PIN,PLASTIC
• Manufacturer: Analog Devices Inc
• Type: Fanout Distribution, Integer N Synthesizer (RF)r

Specifications of ADF4360-6BCPZ

• Pll: Yes
• Input: CMOS
• Output: Clock
• Number Of Circuits: 1
• Ratio - Input:output: 1:2
• Differential - Input:output: No/No
• Frequency - Max: 1.25GHz
• Divider/multiplier: Yes/No
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 24-LFCSP
• Frequency-max: 1.25GHz
• Number Of Elements: 1
• Pll Input Freq (min): 10MHz
• Pll Input Freq (max): 250MHz
• Operating Supply Voltage (typ): 3.3V
• Operating Temp Range: -40C to 85C
• Package Type: LFCSP EP
• Output Frequency Range: 1050 to 1250MHz
• Operating Supply Voltage (min): 3V
• Operating Supply Voltage (max): 3.6V
• Operating Temperature Classification: Industrial
• Pin Count: 24
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-ADF4360-6EBZ1 - BOARD EVALUATION FOR ADF4360-6
• Lead Free Status / Rohs Status: Compliant

ADF4360-6
POWER-UP
Power-Up Sequence
The correct programming sequence for the ADF4360-6 after
power-up is:
1.
2.
3.
Initial Power-Up
Initial power-up refers to programming the part after the
application of voltage to the AV
initial power-up, an interval is required between programming
the control latch and programming the N counter latch. This
interval is necessary to allow the transient behavior of the
ADF4360-6 during initial power-up to have settled.
Table 10. C
C
10 µF
440 nF
N
Value
R counter latch
Control latch
N counter latch
N
Recommended Interval between Control Latch and N Counter Latch
≥ 5 ms
≥ 600 µs
Capacitance vs. Interval and Phase Noise
POWER-UP
CLOCK
DATA
LE
DD
, DV
DD
LATCH DATA
R COUNTER
, V
VCO
, and CE pins. On
Figure 16. ADF4360-6 Power-Up Timing
LATCH DATA
Rev. A | Page 16 of 24
CONTROL
During initial power-up, a write to the control latch powers up
the part and the bias currents of the VCO begin to settle. If
these currents have not settled to within 10% of their steady-
state value and if the N counter latch is then programmed, the
VCO may not be able to oscillate at the desired frequency,
which does not allow the band select logic to choose the correct
frequency band, and the ADF4360-6 may not achieve lock. If
the recommended interval is inserted, and the N counter latch
is programmed, the band select logic can choose the correct
frequency band, and the part locks to the correct frequency.
The duration of this interval is affected by the value of the ca-
pacitor on the C
the close-in noise of the ADF4360-6 VCO. The recommended
value of this capacitor is 10 µF. Using this value requires an in-
terval of ≥ 5 ms between the latching in of the control latch bits
and latching in of the N counter latch bits. If a shorter delay is
required, this capacitor can be reduced. A slight phase noise
penalty is incurred by this change, which is explained further in
Table 10.
CONTROL LATCH WRITE TO
N COUNTER LATCH WRITE
REQUIRED INTERVAL
N
pin (Pin 14). This capacitor is used to reduce
Open-Loop Phase Noise @ 10 kHz Offset
−88 dBc
−87 dBc
LATCH DATA
N COUNTER