AD9640ABCPZ-150 Analog Devices Inc, AD9640ABCPZ-150 Datasheet - Page 46

• Manufacturer Part Number: AD9640ABCPZ-150
• Description: 14Bit 150Msps Dual 1.8V PB Free ADC
• Manufacturer: Analog Devices Inc

Specifications of AD9640ABCPZ-150

• Design Resources: Interfacing ADL5534 to AD9640 High Speed ADC (CN0049)
• Number Of Bits: 14
• Sampling Rate (per Second): 150M
• Data Interface: Serial, SPI™
• Number Of Converters: 2
• Power Dissipation (max): 938mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 64-LFCSP
• Number Of Elements: 2
• Resolution: 14Bit
• Architecture: Pipelined
• Sample Rate: 150MSPS
• Input Polarity: Bipolar
• Input Type: Voltage
• Rated Input Volt: ±1V
• Differential Input: Yes
• Power Supply Requirement: Analog and Digital
• Single Supply Voltage (typ): 1.8V
• Single Supply Voltage (min): 1.7V
• Single Supply Voltage (max): 1.9V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Differential Linearity Error: -0.95LSB/1.5LSB
• Integral Nonlinearity Error: ±5LSB
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 64
• Package Type: LFCSP EP
• Input Signal Type: Differential
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

AD9640
Addr
(Hex)
0x11A
0x11B
MEMORY MAP REGISTER DESCRIPTION
For additional information about functions controlled in
Register 0x00 to Register 0xFF, see the AN-877 Application Note,
Interfacing to High Speed ADCs via SPI.
Sync Control (Register 0x100)
Bit 7—Signal Monitor Sync Enable
Bit 7 enables the sync pulse from the external SYNC input to
the signal monitor block. The sync signal is passed when Bit 7
is high and Bit 0 is high. This is continuous sync mode.
Bits[6:3]—Reserved
Bit 2—Clock Divider Next Sync Only
If the sync enable bit (Address 0x100[0]) is high and the clock
divider sync enable (Address 0x100[1]) is high, Bit 2 allows the
clock divider to sync to the first sync pulse it receives and ignore
the rest. Address 0x100[1] resets after it syncs.
Bit 1—Clock Divider Sync Enable
Bit 1 gates the sync pulse to the clock divider. The sync signal is
passed when Bit 1 is high and Bit 0 is high. This is continuous
sync mode.
Bit 0—Master Sync Enable
Bit 0 must be high to enable any of the sync functions.
Fast Detect Control (Register 0x104)
Bits[7:4]—Reserved
Bits[3:1]—Fast Detect Mode Select
These bits set the mode of the fast detect output bits according
to Table 17.
Bit 0—Fast Detect Enable
Bit 0 is used to enable the fast detect bits. When the fast detect
outputs are disabled, the outputs go into a high impedance state.
In LVDS mode, when the outputs are interleaved, the outputs go
high-Z only if both channels are turned off (power-down/standby/
output disabled). If only one channel is turned off (power-down/
standby/output disabled), the fast detect outputs repeat the data
of the active channel.
Register
Name
Signal Monitor
Result
Channel B
Register 1
(Global)
Signal Monitor
Result
Channel B
Register 2
(Global)
Bit 7
(MSB)
Open
Bit 6
Open
Bit 5
Open
Signal Monitor Result Channel B[15:8]
Bit 4
Open
Rev. B | Page 46 of 52
Bit 3
Fine Upper Threshold (Register 0x106 and Register 0x107)
Register 0x106, Bits[7:0]—Fine Upper Threshold[7:0]
Register 0x107, Bits[7:5]—Reserved
Register 0x107, Bits[4:0]—Fine Upper Threshold[12:8]
These registers provide the fine upper limit threshold. This 13-bit
value is compared to the 13-bit magnitude from the ADC block
and, if the ADC magnitude exceeds this threshold value, the
F_UT flag is set.
Fine Lower Threshold (Register 0x108 and Register 0x109)
Register 0x108, Bits[7:0]—Fine Lower Threshold[7:0]
Register 0x109, Bits[7:5]—Reserved
Register 0x109, Bits[4:0]—Fine Lower Threshold[12:8]
These registers provide a fine lower limit threshold. This 13-bit
value is compared to the 13-bit magnitude from the ADC block
and, if the ADC magnitude is less than this threshold value, the
F_LT flag is set.
Signal Monitor DC Correction Control (Register 0x10C)
Bit 7—Reserved
Bit 6—DC Correction Freeze
When Bit 6 is set high, the dc correction is no longer updated
to the signal monitoring block. It holds the last dc value it
calculated.
Bits[5:2]—DC Correction Bandwidth
These bits set the averaging time of the signal monitor dc correc-
tion function. It is a 4-bit word that sets the bandwidth of the
correction block (see Table 26).
Signal Monitor Result Channel B[19:16]
Bit 2
Bit 1
Bit 0
(LSB)
Default
Value
(Hex)
Default
Notes/
Comments
Read only
Read only