AD9268BCPZ-105 Analog Devices Inc, AD9268BCPZ-105 Datasheet - Page 28

• Manufacturer Part Number: AD9268BCPZ-105
• Description: Dual 16 Bit 105 High SNR ADC
• Manufacturer: Analog Devices Inc

Specifications of AD9268BCPZ-105

• Design Resources: Powering AD9268 with ADP2114 for Increased Efficiency (CN0137)
• Number Of Bits: 16
• Sampling Rate (per Second): 105M
• Data Interface: Serial, SPI™
• Number Of Converters: 2
• Power Dissipation (max): 590mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 64-LFCSP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

AD9268
The signal characteristics must be considered when selecting
a transformer. Most RF transformers saturate at frequencies
below a few megahertz (MHz). Excessive signal power can also
cause core saturation, which leads to distortion.
At input frequencies in the second Nyquist zone and above, the
noise performance of most amplifiers is not adequate to achieve
the true SNR performance of the AD9268. For applications in
which SNR is a key parameter, differential double balun coupling
is the recommended input configuration (see Figure 68). In this
configuration, the input is ac-coupled, and the CML is provided
to each input through a 33 Ω resistor. These resistors compensate
for losses in the input baluns to provide a 50 Ω impedance to
the driver.
In the double balun and transformer configurations, the value of
the input capacitors and resistors is dependent on the input fre-
quency and source impedance and may need to be reduced or
removed. Table 10 displays recommended values to set the RC
network. At higher input frequencies, good performance can be
ANALOG INPUT
ANALOG INPUT
2V p-p
C
D
0.1µF
P
0.1µF
0.1µF
A
R
D
0Ω
0Ω
Figure 69. Differential Input Configuration Using the AD8352
R
Figure 68. Differential Double Balun Input Configuration
G
S
16
1
2
3
4
5
S
AD8352
V
CC
P
8, 13
14
0.1µF
Rev. A | Page 28 of 44
0.1µF
0.1µF
10
11
33Ω
33Ω
0.1µF
0.1µF
achieved by using a ferrite bead in series with a resistor and
removing the capacitors. However, these values are dependent
on the input signal and should be used only as a starting guide.
Table 10. Example RC Network
Frequency
Range
(MHz)
0 to 100
100 to 200
100 to 300
1
An alternative to using a transformer-coupled input at fre-
quencies in the second Nyquist zone is to use the
differential driver. An example is shown in Figure 69. See the
AD8352 data sheet for more information.
0.1µF
200Ω
200Ω
In this configuration, R1 is a ferrite bead with a value of 10 Ω @ 100 MHz.
0.1µF
R1
R1
0.1µF
C2
C1
C2
R
R
C
R1 Series
(Ω Each)
33
10
10
R2
R2
1
VIN+
VIN–
AD9268
VIN+
VIN–
C1 Differential
(pF)
5
5
Remove
AD9268
VCM
VCM
R2 Series
(Ω Each)
15
10
66
AD8352
C2 Shunt
(pF Each)
15
10
Remove