AD9239-250KITZ Analog Devices Inc, AD9239-250KITZ Datasheet - Page 23

• Manufacturer Part Number: AD9239-250KITZ
• Description: Quad 12 Bit 250 MSPS Serial ADC-Evl Brd
• Manufacturer: Analog Devices Inc

Specifications of AD9239-250KITZ

• Number Of Adc's: 4
• Number Of Bits: 12
• Sampling Rate (per Second): 250M
• Data Interface: Serial
• Inputs Per Adc: 1 Differential
• Input Range: 1.25 Vpp
• Power (typ) @ Conditions: 1.526W @ 250MSPS
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Utilized Ic / Part: AD9239
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Digital Start-Up Sequence
The output digital data from the AD9239 is coded and packetized,
which requires the device to have a certain start-up sequence.
The following steps should be initialized by the user to capture
coherent data at the receiving logic.
1.
2.
3.
4.
5.
6.
To minimize skew and time misalignment between each
channel of the digital outputs, the following actions should be
taken to ensure that each channel data packet is within ±1 clock
cycle of its specified switching time. For some receiver logic,
this is not required.
1.
2.
3.
Digital Outputs and Timing
The AD9239 has differential digital outputs that power up on
default. The driver current is derived on chip and sets the output
current at each output equal to a nominal 4 mA. Each output
presents a 100 Ω dynamic internal termination to reduce unwanted
reflections
Initialize a soft reset via Bit 5 of Register 0 (see Table 15).
All PGMx pins are automatically initialized as sync pins by
default. These pins can be used to lock the FPGA timing
and data capture during initial startup. These pins are
respective to each channel (PGM3 = Channel A).
Each sync pin is held low until its respective PGMx pin
receives a high signal input from the receiver, during which
time the ADC outputs a training pattern.
The training pattern defaults to the values implemented by
the user in Register 19 through Register 20.
When the receiver finds the frame boundary, the sync
identification is deasserted high via the sync pin or via a
SPI write. The ADC outputs the valid data on the next packet
boundary. The time necessary for sync establishment is highly
dependent on the receiver logic processing. Refer to the
Switching Specifications section; the switching timing is
directly related to the ADC channel.
Once steady state operation for the device has occurred,
these pins can each be assigned to be a standby option by
using Register 53 (see Table 15). All other pins act as
universal sync pins.
Full power-down through external PDWN pin.
Chip reset via external RESET pin.
Power back up by releasing external PDWN pin.
Rev. B | Page 23 of 40
A 100 Ω differential termination resistor should be placed at each
receiver input to result in a nominal 400 mV p-p swing at the
receiver. Alternatively, single-ended 50 Ω termination can be
used. When single-ended termination is used, the termination
voltage should be DRVDD/2; otherwise, ac coupling capacitors
can be used to terminate to any single-ended voltage.
The AD9239 digital outputs can interface with custom application-
specific integrated circuits (ASICs) and field-programmable gate
array (FPGA) receivers, providing superior switching performance
in noisy environments. Single point-to-point net topologies are
recommended with a single differential 100 Ω termination resistor
placed as close to the receiver logic as possible. The common mode
of the digital output automatically biases itself to half the supply
of DRVDD if dc-coupled connecting is used. For receiver logic
that is not within the bounds of the DRVDD supply, an ac-coupled
connection should be used. Simply place a 0.1 μF capacitor on
each output pin and derive a 100 Ω differential termination
close to the receiver side.
If there is no far-end receiver termination or there is poor
differential trace routing, timing errors may result. To avoid
such timing errors, it is recommended that the trace length be
less than 6 inches and that the differential output traces be close
together and at equal lengths.
OUTPUT SWING = 400mV p-p
OUTPUT SWING = 400mV p-p
DOUT + x
DOUT – x
Figure 61. DC-Coupled Digital Output Termination Example
DRVDD
Figure 62. AC-Coupled Digital Output Termination Example
DOUT + x
DOUT – x
DRVDD
0.1µF
0.1µF
DIFFERENTIAL
DIFFERENTIAL
TRACE PAIR
TRACE PAIR
100Ω
100Ω
100Ω
100Ω
V
OR
RXCM
RECEIVER
V
V
CM
CM
RECEIVER
= Rx V
= DRVDD/2
AD9239
CM