AD7226BRS-REEL Analog Devices Inc, AD7226BRS-REEL Datasheet - Page 8

• Manufacturer Part Number: AD7226BRS-REEL
• Description: Digital To Analog Converter
• Manufacturer: Analog Devices Inc

Specifications of AD7226BRS-REEL

• Rohs Status: RoHS non-compliant
• Settling Time: 4µs
• Number Of Bits: 8
• Data Interface: Parallel
• Number Of Converters: 4
• Voltage Supply Source: Dual ±
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 20-SSOP
• Power Dissipation (max): -

AD7226
SPECIFICATION RANGES
In order for the DACs to operate to their specifications, the
reference voltage must be at least 4 V below the V
supply voltage. This voltage differential is required for correct
generation of bias voltages for the DAC switches.
The AD7226 is specified to operate over a V
+12 V ± 5% to +15 V ± 10% (i.e., from +11.4 V to +16.5 V)
with a V
+15 V ± 5% V
improved zero code error, improved output sink capability with
outputs near AGND and improved negative-going settling time.
Performance is specified over a wide range of reference voltages
from 2 V to (V
of standard reference generators to be used such as the AD780,
a 2.5 V band gap reference and the AD584, a precision 10 V
reference. Note that in order to achieve an output voltage range
of 0 V to 10 V a nominal 15 V ± 5% power supply voltage is
required by the AD7226.
SETTLING TIME
The output stage of the buffer amplifiers consists of a bipolar
NPN transistor from the V
V
fiers. As mentioned in the op amp section, in single supply
operation the NMOS transistor will come out of saturation as the
output voltage approaches AGND and will act as a resistive load
of approximately 2 kW to AGND. As a result, the settling time for
negative-going signals approaching AGND in single supply opera-
tion will be longer than for dual supply operation where the
current load of 400 mA is maintained all the way down to AGND.
Positive-going settling-time is not affected by V
The settling-time for the AD7226 is limited by the slew-rate of
the output buffer amplifiers. This can be seen from Figure 6
which shows the dynamic response for the AD7226 for a full
scale change. Figures 7a and 7b show expanded settling-time
photographs with the output waveforms derived from a differen-
tial input to an oscilloscope. Figure 7a shows the settling time
for a positive-going step and Figure 7b shows the settling time
for a negative-going output step.
SS
. V
SS
DATA
V
OUT
SS
is the negative power supply for the output buffer ampli-
Figure 6. Dynamic Response (V
of –5 V ± 10%. Operation is also specified for a single
DD
DD
– 4 V) with dual supplies. This allows a range
supply. Applying a V
DD
line and a constant current load to
SS
of –5 V results in
DD
SS
SS
= –5 V)
range from
.
DD
power
–8–
GROUND MANAGEMENT
AC or transient voltages between AGND and DGND can cause
noise at the analog output. This is especially true in micropro-
cessor systems where digital noise is prevalent. The simplest
method of ensuring that voltages at AGND and DGND are
equal is to tie AGND and DGND together at the AD7226. In
more complex systems where the AGND and DGND intertie is
on the backplane, it is recommended that two diodes be con-
nected in inverse parallel between the AD7226 AGND and
DGND pins (IN914 or equivalent).
Unipolar Output Operation
This is the basic mode of operation for each channel of the
AD7226, with the output voltage having the same positive
polarity as +V
(V
section which outlines the advantages of having negative V
The code table for unipolar output operation is shown in Table
II. Note that the voltage at V
respect to DGND in order to prevent parasitic transistor turn-on.
Connections for the unipolar output operation are shown in
Figure 8.
SS
DATA
DATA
Figure 7b. Negative Step Settling Time (V
Figure 7a. Positive Step Settling Time (V
O/P
O/P
= AGND) or with positive/negative supplies (see op amp
REF
. The AD7226 can be operated single supply
REF
must never be negative with
SS
SS
= –5 V)
= –5 V)
+1/2 LSB
–1/2 LSB
+1/2 LSB
–1/2 LSB
REV.
SS
).
D