A1152LLHLT-T Allegro Microsystems Inc, A1152LLHLT-T Datasheet - Page 9

• Manufacturer Part Number: A1152LLHLT-T
• Description: 2-Wire Factory Programmed Switch
• Manufacturer: Allegro Microsystems Inc
• Type: Unipolar Switchr

Specifications of A1152LLHLT-T

• Sensing Range: 110G Trip, 45G Release
• Voltage - Supply: 3 V ~ 24 V
• Current - Supply: 6.9mA
• Output Type: Digital, Open Collector
• Features: High Speed
• Operating Temperature: -40°C ~ 150°C
• Package / Case: SOT-23W
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Output (max): -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 620-1378-2

A1152, A1153,
A1155, and A1156
Power Derating
The device must be operated below the maximum junction tem-
perature of the device, T
peak conditions, reliable operation may require derating supplied
power or improving the heat dissipation properties of the appli-
cation. This section presents a procedure for correlating factors
affecting operating T
Allegro MicroSystems Web site.)
The Package Thermal Resistance, R
marizing the ability of the application and the device to dissipate
heat from the junction (die), through all paths to the ambient air.
Its primary component is the Effective Thermal Conductivity, K,
of the printed circuit board, including adjacent devices and traces.
Radiation from the die through the device case, R
small component of R
motion are significant external factors, damped by overmolding.
The effect of varying power levels (Power Dissipation, P
be estimated. The following formulas represent the fundamental
relationships used to estimate T

For example, given common conditions such as: T
V

A worst-case estimate, P
able power level (V
T
J
CC
(max), at a selected R
T = P
= 12 V, I
T = P
CC
P
D
= 4 mA, and R
= V
T
D
J
P
T
CC
= T
D
J
J
×
CC
. (Thermal data is also available on the
JA
= T
(max), I
= V
A
R
JA
J
×
D
(max). Under certain combinations of
. Ambient air temperature, T
A
JA
+ T = 25°C + 7°C = 32°C
D
(max), represents the maximum allow-
IN
I
+ ΔT
and T
×
CC
×
= 48 mW
CC
R
= 12 V
I
JA
J
JA
, at P
IN
(max)), without exceeding
A
.
= 140 °C/W, then:
JA
D
×
.
×
, is a figure of merit sum-
4 mA = 48 mW
140 °C/W = 7°C
JC
A
= 25°C,
, is relatively
A
, and air
D
), can
(1)
(2)
(3)
Example: Reliability for V
low-K PCB.
Observe the worst-case ratings for the device, specifically:
R
I
Calculate the maximum allowable power level, P
invert equation 3:
This provides the allowable increase to T
power dissipation. Then, invert equation 2:
Finally, invert equation 1 with respect to voltage:
The result indicates that, at T
dissipate adequate amounts of heat at voltages ≤V
Compare V
able operation between V
R
and V
CC
JA
JA
V
T
(max) = 17 mA.
CC(est)
. If V
= 165 °C/W, T
P
CC
max
Chopper-Stabilized, Two Wire
(max) is reliable under these conditions.
D
= T
= P
CC(est)
(max) = T
CC(est)
J
D
(max) – T
(max) ÷ I
≥ V
to V
J
(max) = 165°C, V
CC
max
CC
(max), then operation between V
A
CC
(max). If V
CC(est)
Hall-Effect Switches
= 165 °C – 150 °C = 15 °C
÷ R
CC
(max) = 91 mW ÷ 17 mA = 5 V
115 Northeast Cutoff
1.508.853.5000; www.allegromicro.com
Allegro MicroSystems, Inc.
Worcester, Massachusetts 01615-0036 U.S.A.
A
JA
at T
, the application and device can
and V
= 15°C ÷ 165 °C/W = 91 mW
A
= 150°C, package UA, using a
CC(est)
CC
CC
(max) = 24 V, and
(max) requires enhanced
J
resulting from internal
≤ V
CC
(max), then reli-
D
CC(est)
(max). First,
.
CC(est)
9