M1-SYSMGMT-DEV-KIT-FP3 Actel, M1-SYSMGMT-DEV-KIT-FP3 Datasheet - Page 11

• Manufacturer Part Number: M1-SYSMGMT-DEV-KIT-FP3
• Description: MCU, MPU & DSP Development Tools System Management Development Kit
• Manufacturer: Actel

Specifications of M1-SYSMGMT-DEV-KIT-FP3

• Processor To Be Evaluated: AFS1500-FG484
• Interface Type: RS-232, USB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Hardware Components
Power Supplies
Jumper Settings
M1AFS1500-FG484
A3P250-FG144
M1 System Management Board User’s Guide
This chapter describes the hardware components of the M1 System Management Board.
A 9 V power supply is provided with the kit. The 9 V brick is connected to the J1 connector on the board. This power
supply feeds the input voltage of three LDO-type regulators—U1, U2, and U3—through a slide switch, SW7. The
switch toggles between two positions On-Off. The regulators provide three voltages 5 V, 3.3 V and 1.5 V.
Table 2-1
JP13 is a two-pin jumper that provides V
the M1AFS1500-FG484 and A3P250-FG144 parts. While programming these two parts, make sure this location has a
jumper.
JP35 is a two-pin jumper that provides V
M1AFS1500-FG484 and A3P250-FG144 parts. While programming these two parts, make sure this location has a
jumper.
JP1 is a three-pin jumper that provides 1.5 V to the M1AFS1500-FG484 part.
JP1.1-2 connects the 1.5 V going to the M1AFS1500-FG484 part to 1.5_INT. This voltage is generated internally by
the M1AFS1500-FG484 part through an on-chip regulator powered by the 3.3 V supply. JP1.2-3 connects the 1.5 V
going to the M1AFS1500-FG484 part to voltage 1.5_EXT. This voltage is generated externally by the on-board
regulator U3.
This is the Actel ARM-enabled Fusion FPGA demonstrated on the System Management Board and located at U23.
Refer to
This device is an Actel FPGA used purely due to the limitation on the number of I/Os on the M1AFS1500-FG484
part. This device controls all user interfaces: LCD, key pads, DIP switch, LEDs, etc. The M1AFS1500-FG484 and the
A3P250 device communicate via a UART interface using the Actel CoreUART IP. Refer to
on page 63
“M1AFS1500-FG484 Pin List” on page 47
illustrates LEDs provided to ensure that all the voltage reach the correct state.
Red LED
Yellow LED
Yellow LED
Yellow LED
Yellow LED
for pin list information.
LED
Designator
Reference
D26
D29
D25
D21
D27
JTAG
PUMP
with a 3.3 V supply. V
Off
On
Off
Off
Off
Off
with a 3.3 V supply. V
Table 2-1 · LEDs
SW7
for pin list information.
On
On
On
On
On
On
JTAG
PUMP
9 V input voltage before switch SW7
9 V input voltage after switch SW7
5 V supply
3.3 V supply
1.5 V supply
is needed to power up the JTAG circuitry of
is needed while programming the
Description
“A3P250-FG144 Pin List”
2
11