2ED300E17-S Infineon Technologies, 2ED300E17-S Datasheet

Page 1

... EiceDRIVER EiceDRIVER 2ED300E17-S Dual Evaluation Board for IGBT driver 2ED300C17-S Technical Documentation prepared by : M.Hornkamp date of publication: 01.05.2003 approved by: Mark Münzer revision: 1.0 SN: 24690 status: evaluation board ™ ™ eupec GmbH Max-Planck-Straße 5 D-59581 Warstein Author: Michael Hornkamp Tel. +49(0)2902 764-0 Fax +49(0)2902 764-1150 Email: info@eupec ...

Page 2

... During work after turn-off it has to be observed that components heat up during operation. Contact with these can cause burning. • The drivers are mounted electrically and mechanically into the 2ED300E17-S mother board by soldering. The mechanical strength has to be verified by the user and, if necessary, assured with appropriate tests. ...

Page 3

... EiceDRIVER General information for the evaluation board 2ED300E17-S: The evaluation board 2ED300E17 application add-on for the Dual IGBT driver 2ED300C17-S. In this function the evaluation board supports the application of the 2ED300C17-S. Documented is the minimum required circuitry of the 2ED300C17-S. Special circuits such as “Active Clamping“, separate Rgon/ Rgoff or use of the EDFA (see datasheet of the 2ED300C17-S chapter 3 ...

Page 4

... EiceDRIVER Mounting and dimensions : The half-bridge driver 2ED300C17-S is inserted onto the component side of the 2ED300E17-S and soldered cleanly from the back. Make sure not to cause shorts between the pins of the driver important that the driver is inserted as far as possible into the evaluation board. ...

Page 5

... Technische Information / Technical Information EiceDRIVER EiceDRIVER Circuit diagram of the evaluation board 2ED300E17-S: Inputs and Outputs of the 2ED300E17-S X1 n.c. Pin1 IN B; PWM signal inputs for channel B Pin2 Fault The fault output indicates a fault. Pin3 IN A; PWM signal inputs for channel A Pin4 Reset Pin5 n ...

Page 6

... NOTE ! The PWM inputs have a trigger level of +10V. www.eupec.com ™ ™ 2ED300E17-S Soft Shut Down: R The R R4/R3 is preset to 10kOhm. The SSD performance of the SSD depends on the R has to be adapted. See also the datasheet of the 2ED300C17-S chapter 3.8. ...

Page 7

... It is equally important to place the collector diodes appropriately. Make sure to be aware of the possible high voltages. Should an “Active Clamping“ the datasheet of the 2ED300C17-S chapter 3.10 be used, the sense input utilised. The plug used for “Molex“- type www.eupec.com ™ ™ 2ED300E17-S X2: 1=V 2=Gate A 3=COM A 4= Sense ...

Page 8

... Technische Information / Technical Information EiceDRIVER EiceDRIVER Layout and component print : www.eupec.com ™ ™ 2ED300E17-S On the component side of the 2ED300E17-S PCB is a print layout showing all relevant components. The corresponding explanations are to be found on page 6 and in the datasheet of the 2ED300C17-S www.EiceDRIVER.com Seite/Page 8 ...

Page 9

... EiceDRIVER Type designation : ™ ™ EiceDRIVER EiceDRIVER eupec IGBT controlled efficiency DRIVER 2ED300C17-ST For example: www.eupec.com ™ ™ 2ED300E17-S Insulation class Base insulated S = Safe separation ST= Safe separation / traction Voltage class 600V 12 = 1200V 17 = 1700V and 1200V 33 = 3300V 65 = 6500V Driver type Driver core with DC/DC ...