71M6512-DB Maxim Integrated Products, 71M6512-DB Datasheet - Page 120
71M6512-DB
Manufacturer Part Number
71M6512-DB
Description
Power Management Modules & Development Tools 71M6512 DEMO BOARD 71M6512 DEMO BOARD
Manufacturer
Maxim Integrated Products
Datasheet
1.71M6521DE-DB.pdf
(138 pages)
- Current page: 120 of 138
- Download datasheet (2Mb)
The state of bits RS1 and RS0 select the working registers bank as follows:
The stack pointer is a 1-byte register initialized to 07H after reset. This register is incremented before PUSH and CALL
instructions, causing the stack to begin at location 08H.
The data pointer (DPTR) is 2 bytes wide. The lower part is DPL, and the highest is DPH. It can be loaded as a 2-byte
register (MOV DPTR,#data16) or as two registers (e.g. MOV DPL,#data8). It is generally used to access external code
or data space (e.g. MOVC A,@A+DPTR or MOVX A,@DPTR respectively).
The program counter (PC) is 2 bytes wide initialized to 0000H after reset. This register is incremented during the
fetching operation code or when operating on data from program memory.
Port registers ‘P0’, ‘P1’, and ‘P2’ are Special Function Registers. The contents of the SFR can be observed on
corresponding pins on the chip. Writing a ‘1’ to any of the ports causes the corresponding pin to be at high level (VCC),
and writing a ‘0’ causes the corresponding pin to be held at low level (GND).
All DIO ports on the chip are bi-directional. Each of them consists of a Latch (SFR ‘P0’ to ‘P2’), an output driver, and an
input buffer, therefore the MPU can output or read data through any of these ports if they are not used for alternate
purposes.
The 80515 has two 16-bit timer/counter registers: Timer 0 and Timer 1. These registers can be configured for counter
or timer operations.
In timer mode, the register is incremented every machine cycle meaning that it counts up after every 12 periods of the
MPU clock signal.
In counter mode, the register is incremented when the falling edge is observed at the corresponding input pin t0 or t1.
Since it takes 2 machine cycles to recognize a 1-to-0 event, the maximum input count rate is 1/2 of the oscillator
frequency. There are no restrictions on the duty cycle, however to ensure proper recognition of 0 or 1 state, an input
should be stable for at least 1 machine cycle.
are used to select the appropriate mode.
Revision 1.7
Four operating modes can be selected for Timer 0 and Timer 1. Two Special Function Registers (TMOD and TCON)
Stack Pointer
Data Pointer
Program Counter
Ports
Timers 0 and 1
RS1/RS0
00
01
10
11
© Copyright 2005-2007 TERIDIAN Semiconductor Corporation
Table 6-20: Register Bank Location
Bank selected
Bank 0
Bank 1
Bank 2
Bank 3
TERIDIAN Proprietary
Location
(00H – 07H)
(08H – 0FH)
(10H – 17H)
(18H – 1FH)
71M652X Software User’s Guide
120 of 138
Related parts for 71M6512-DB
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Current & Power Monitors & Regulators Residential Meter Extended Io
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Current & Power Monitors & Regulators Gang Programmer Base Unit+6512 Socket Brd
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Current & Power Monitors & Regulators Residential Meter Extended Io
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products