MAX16946EVKIT# Maxim Integrated Products, MAX16946EVKIT# Datasheet - Page 2

• Manufacturer Part Number: MAX16946EVKIT#
• Description: Power Management Modules & Development Tools 18V Remote Antenna C urrent-Sense and LDO
• Manufacturer: Maxim Integrated Products
• Type: Current Monitors & Regulatorsr

Specifications of MAX16946EVKIT#

• Maximum Operating Temperature: + 105 C
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 4.5 V to 18 V
• Product: Power Management Development Tools
• For Use With/related Products: MAX16946
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

MAX16946 Evaluation Kit
Note: Indicate that you are using the MAX16946 when contacting these component suppliers.
• MAX16946 EV kit
• 18V, 200mA DC power supply
• Load
• Two voltmeters
The EV kit is fully assembled and tested. Follow the steps
below to verify board operation. Caution: Do not turn
on power supply until all connections are completed.
1) Verify that all jumpers are in their default position, as
2) Adjust the power supply to 10V.
2
Diodes Incorporated
Murata Electronics North America, Inc.
ON Semiconductor
Panasonic Corp.
Sumida Corp.
TDK Corp.
DESIGNATION
R13, R14, R15
______________________________________________________________________________________
shown in Table 1.
R7, R9
R10
R11
R12
R16
R3
R4
R5
R6
R8
SUPPLIER
QTY
1
1
1
1
2
1
1
1
1
3
1
33kI Q1% resistor (0603)
86.6kI Q1% resistor (0603)
30.1kI Q1% resistor (0603)
18.7kI Q1% resistor (0603)
4.7kI Q1% resistors (0603)
33.2kI Q1% resistor (0603)
2.2kI Q5% resistor (0603)
4.7kI Q5% resistor (0603)
10kI Q5% resistor (0603)
100kI Q5% resistors (0603)
62kI Q5% resistor (0603)
Required Equipment
DESCRIPTION
Quick Start
Procedure
805-446-4800
770-436-1300
602-244-6600
847-545-6700
847-803-6100
800-344-2112
PHONE
3) Adjust the load to 30mA.
4) Connect the power supply between the VIN and
5) Connect the load between the REG_OUT and GND
6) Connect the first voltmeter between the REG_OUT
7) Connect the second voltmeter between the AOUT
8) Enable the power supply and the load.
9) Verify that the first voltmeter displays 5V.
10) Verify that the second voltmeter displays 790mV.
DESIGNATION
GND PCB pads on the EV kit.
PCB pads on the EV kit.
and GND PCB pads on the EV kit.
and GND PCB pads on the EV kit.
SW1
U1
U2
U3
—
—
Component List (continued)
QTY
www.diodes.com
www.murata-northamerica.com
www.onsemi.com
www.panasonic.com
www.sumida.com
www.component.tdk.com
1
1
1
1
7
1
Component Suppliers
Pushbutton switch
Current-sense LDO
(16 TQFN-EP)
Maxim MAX16946GTE/V+
General-purpose timer (8 SO)
Maxim ICM7555ESA+
5V LDO (8 SO-EP)
Maxim MAX15006BASA+
Shunts
PCB: MAX16946 EVALUATION
KIT
WEBSITE
DESCRIPTION