109100154 TE Connectivity, 109100154 Datasheet
109100154
Specifications of 109100154
Related parts for 109100154
109100154 Summary of contents
Page 1
Data Sheet March 2008 RoHS Compliant The FLTR100V10 Filter Module is encapsulated in a small, nonconductive plastic case. Application Common-mode and differential-mode filtering of n power supply dc input and output lines Computer applications n Communications equipment n Description The ...
Page 2
Vdc Input Maximum Maximum Introduction High-density power modules are usually designed to operate at a high switching frequency to reduce the size of the internal filter components. The small EMI filters internal to the modules are often ...
Page 3
March 2008 Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage and temperature conditions. Parameter Resistance per Leg Maximum Average Current ( °C, 2.03 m/s (400 lfm) air) A Maximum Average Current ( ...
Page 4
March 2008 Characteristics (continued) 0 -20 -40 -60 -80 -100 0.1 1.0 FREQUENCY (MHz) Figure 3. Typical Differential-Mode Insertion Loss Ω Circuit 1• ...
Page 5
Vdc Input Maximum Maximum Application Conducted noise on the input power lines can occur as either differential-mode or common-mode noise cur- rents. Differential-mode noise is measured between the two input lines, and is found mostly at the ...
Page 6
Vdc Input Maximum Maximum Application (continued) Vdc INPUT(+) V (+) V (+) I O FILTER MODULE Vdc INPUT(-) V (-) V (-) I O GND CHASSIS GROUND Note: C1 through C4 can be 0.01 µF to 0.1 ...
Page 7
March 2008 Application (continued) Vdc INPUT(+) V (+) V (+) I O FILTER MODULE Vdc INPUT(-) V (-) V (-) I O GND CHASSIS GROUND Note: C1 through C4 and C6 through C9 can be 0.01 µF to 0.1 µF. ...
Page 8
March 2008 Application (continued) Figures 9 and 10 show some experimental results obtained by using the filter module, together with the recommended external components shown in Figures 6 and 7. The JW075A5 module is a lower-noise version of the standard ...
Page 9
Vdc Input Maximum Maximum Other Considerations (continued) Figure 9. JW075A1 Conducted Noise with Filter 9 9 8-1387(F) Figure 10. JW075A5 Conducted Noise with Filter March 2008 8-1388(F) Lineage Power ...
Page 10
Vdc Input Maximum Maximum Outline Diagram Dimensions are in millimeters and (inches). Tolerances: x.x ± 0.5 mm (0.02 in.), x.xx ± 0.25 mm (0.010 in.). Top View Side View 0.51 (0.020) Bottom View 3.8 (0.15) 19.05 (0.750) ...
Page 11
March 2008 Recommended Hole Pattern Component-side footprint. Dimensions are in millimeters and (inches). Tolerances: x.x ± 0.5 mm (0.02 in.), x.xx ± 0.25 mm (0.010 in.). Note: Do not route copper paths beneath power module standoffs. Lineage Power 75 Vdc ...
Page 12
Vdc Input Maximum Maximum Post Solder Cleaning and Drying Consid- eratrions Post solder cleaning is usually the final circuit-board assembly process prior to electrical board testing.The result of inadequate cleaning and drying can affect both the reliability ...
Page 13
... Standard Pin Length 108799131 0.145 in. Pin Length 108799123 0.110 in. Pin Length 108997607 0.180 in. Pin Length CC109103801 0.180 in. Pin Length RoHS compliant 109100154 Standard Pin Length RoHS compliant CC109103264 0.145 in. Pin Length RoHS compliant CC1091103272 0.110 in. Pin Length RoHS compliant Device Code ...