1648317-1 TE Connectivity, 1648317-1 Datasheet
1648317-1
Specifications of 1648317-1
Related parts for 1648317-1
1648317-1 Summary of contents
Page 1
All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions are in millimeters [and NOTE inches]. Unless otherwise specified, dimensions have a tolerance of +0.13 [+.005] and angles have a tolerance of +2_. i Figures and ...
Page 2
Lower Drawer Chamfered Pin Side Edge Guide Post Cavity Guide Post Dual Power Pin Side Double Drawer Pin Side Crimp Type Solder Type Contact Contact 2. REFERENCE MATERIAL 2.1. Revision Summary Updated document to corporate requirements S Added new information ...
Page 3
Customer Assistance Product Part Number 1648578 and Product Code D033 are representative numbers of the ELCON Drawer Series Connectors. Use of these numbers will identify the product line and expedite your inquiries through a service network established to help ...
Page 4
Special Features The length of the pin contacts (except size 0 and 4), designated by standard, pre--mate, and post--mate, varies among contact sizes and applies to the portion of the contact that protrudes from the connector after insertion (socket ...
Page 5
Wire Strip Length Wire Strip Length Note: Not to Scale D Refer to MS 3348, “Contact Bushing, Electrical, Wire Barrel” 3.6. Crimp Type Contacts Crimp contact to wire according to instructions packaged with applicable tooling. These requirements apply equally to ...
Page 6
Each crimp dimension represents the functional range of wire and contact combination. The developed crimp NOTE configuration is unique for each tool design and is acceptable provided the crimp height is within the functional range. i For crimp dimensions relating ...
Page 7
Contact the Product Information Center at the number listed at the bottom of page 1 for suitability of other board NOTE materials and thicknesses Board Tolerance Maximum allowable bow of the pc board shall be 0.03 mm ...
Page 8
D. PC Board Layout The mounting holes and contact holes in the pc board must be precisely located to ensure proper placement and optimum performance of the connector. Design the pc board using the dimensions provided in Figure 8. A ...
Page 9
Middle Drawer Socket Side Rev D Figure 8 (cont’d) Tyco Electronics Corporation 75A Middle Drawer Pin Side ...
Page 10
Mini Drawer Pin Side Lower Drawer Pin Side Lower Drawer Socket Side Figure 8 (cont’d) Tyco Electronics Corporation Mini Drawer Socket Side Rev D ...
Page 11
Quad Power 18.42 [0.725] 5.40 [0.21] 43.18 [1.700] 18.42 [0.725] PANEL CUT OUT 24.89 [0.980] 43.18 [1.700] Dual Power 43.18 [1.700] 24.89 [0.980] 16.51 [.650] 25.40 [1.00] PANEL CUT OUT 2X THREADED INSERT 18.42 [0.725] Rev D 2X 8.89 [0.350] ...
Page 12
E. PC Board Hole Dimensions The solder type contacts may be used with or without plated through holes. If plated, the drilled hole size, plating types, and plating thickness are dependent on the application requirements. The finished hole size must ...
Page 13
A. Flux Selection Wire lead and contact wire barrel interior shall be fluxed prior to soldering using a mildly active rosin. Flux must be compatible with manufacturing, safety, and health guidelines. B. Cleaning After cleaning, removal of fluxes, residues, and ...
Page 14
Mounting Hardware The connectors can be float mounted or fixed mounted to a backplane or chassis. The float mount shoulder screws are designed to secure a connector to a panel. The panel must flex and be of sufficient gauge ...
Page 15
Connector Mating and Alignment The pre--installed guide pins and molded--in guide posts ensure positive mating of connectors. In addition, because of their symmetrical design, the low power connectors have a polarizing feature: a rib in the guide post cavity ...
Page 16
Repair Damaged connectors must be removed, discarded, and replaced. Connectors with solder type contacts will require desoldering of all contact solder tails. Solder type contacts are not removable from the housing assembly. Damaged crimp type contacts must be removed ...
Page 17
VISUAL AID Figure 17 shows a typical application of the ELCON Drawer Series Connectors. This illustration should be used by production personnel to ensure a correctly applied product. Applications which DO NOT appear correct should be inspected using the ...