08055E104ZAT2A AVX Corporation, 08055E104ZAT2A Datasheet - Page 13

• Manufacturer Part Number: 08055E104ZAT2A
• Description: CAPACITOR CERAMIC, 0.1UF, 50V, Z5U, 0805
• Manufacturer: AVX Corporation
• Series: 0805r

Specifications of 08055E104ZAT2A

• Tolerance (+ Or -): -20% to 80%
• Voltage: 50VDC
• Temp Coeff (dielectric): Z5U
• Operating Temp Range: 10C to 85C
• Mounting Style: Surface Mount
• Construction: SMT Chip
• Case Style: Ceramic Chip
• Failure Rate: Not Required
• Wire Form: Not Required
• Product Length (mm): 2.01mm
• Product Depth (mm): 1.25mm
• Product Height (mm): 1.3mm
• Product Diameter (mm): Not Requiredmm
• Capacitance: .1uF
• Package / Case: 0805
• Dielectric Characteristic: Z5U
• Capacitance Tolerance: +80, -20%
• Voltage Rating: 50VDC
• Capacitor Case Style: 0805
• No. Of Pins: 2
• Capacitor Mounting: SMD
• Rohs Compliant: Yes
• Tolerance: - 20 %, 80 %
• Operating Temperature Range: + 10 C to + 85 C
• Temperature Coefficient / Code: Z5U
• Product: General Type MLCCs
• Dimensions: 0.049 in W x 0.079 in L x 0.930 mm H
• Termination Style: SMD/SMT
• Lead Free Status / RoHS Status: Compliant

X7R Dielectric
Specifications and Test Methods
12
Resistance to
Resistance to
Operating Temperature Range
Solder Heat
Load Life
Humidity
Stresses
Thermal
Flexure
Shock
Load
Insulation Resistance
Dielectric Strength
Dissipation Factor
Parameter/Test
Capacitance
Solderability
Capacitance
Capacitance
Capacitance
Capacitance
Capacitance
Appearance
Appearance
Appearance
Appearance
Appearance
Resistance
Resistance
Resistance
Resistance
Resistance
Dissipation
Dissipation
Dissipation
Dissipation
Dissipation
Insulation
Insulation
Insulation
Insulation
Insulation
Dielectric
Dielectric
Dielectric
Dielectric
Variation
Variation
Strength
Variation
Strength
Variation
Strength
Variation
Strength
Factor
Factor
Factor
Factor
Factor
No defects, <25% leaching of either end terminal
≥ 95% of each terminal should be covered
No breakdown or visual defects
≥ Initial Value x 0.3 (See Above)
≥ Initial Value x 0.3 (See Above)
Meets Initial Values (As Above)
Meets Initial Values (As Above)
Meets Initial Values (As Above)
Meets Initial Values (As Above)
Meets Initial Values (As Above)
Meets Initial Values (As Above)
≤ Initial Value x 2.0 (See Above)
≤ Initial Value x 2.0 (See Above)
100,000MΩ or 1000MΩ - µF,
Meets Initial Values (As Above)
Meets Initial Values (As Above)
Meets Initial Values (As Above)
X7R Specification Limits
≤ 2.5% for ≥ 50V DC rating
≤ 3.0% for ≥ 25V DC rating
≤ 3.5% for ≥ 16V DC rating
≤ 5.0% for ≥ 10V DC rating
Within specified tolerance
≥ Initial Value x 0.3
No visual defects
-55ºC to +125ºC
whichever is less
with fresh solder
No visual defects
No visual defects
No defects
≤ ±12.5%
≤ ±12.5%
≤ ±12%
≤ ±7.5%
≤ ±7.5%
1-5 seconds, w/charge and discharge current
Charge device with 300% of rated voltage for
seconds. Store at room temperature for 24 ± 2
hours before measuring electrical properties.
Dip device in eutectic solder at 260ºC for 60
Step 1: -55ºC ± 2º
Step 2: Room Temp
Step 3: +125ºC ± 2º
Step 4: Room Temp
Repeat for 5 cycles and measure after
24 ± 2 hours at room temperature
Dip device in eutectic solder at 230 ± 5ºC
85% ± 5% relative humidity for 1000 hours
Store in a test chamber set at 85ºC ± 2ºC/
Charge device with twice rated voltage in
Remove from test chamber and stabilize
Remove from chamber and stabilize at
Charge device with rated voltage for
at room temperature for 24 ± 2 hours
60 ± 5 secs @ room temp/humidity
(+48, -0) with rated voltage applied.
room temperature and humidity for
test chamber set at 125ºC ± 2ºC
24 ± 2 hours before measuring.
Temperature Cycle Chamber
Measuring Conditions
Voltage: 1.0Vrms ± .2V
for 1000 hours (+48, -0)
Test Time: 30 seconds
limited to 50 mA (max)
Freq.: 1.0 kHz ± 10%
for 5.0 ± 0.5 seconds
before measuring.
Deflection: 2mm
90 mm
1mm/sec
30 ± 3 minutes
≤ 3 minutes
≤ 3 minutes
30 ± 3 minutes