GCM21B5C1H223JA16L Murata, GCM21B5C1H223JA16L Datasheet - Page 17

• Manufacturer Part Number: GCM21B5C1H223JA16L
• Manufacturer: Murata

Specifications of GCM21B5C1H223JA16L

• Tolerance (+ Or -): 5%
• Voltage: 50VDC
• Temp Coeff (dielectric): C0G
• Operating Temp Range: -55C to 125C
• Mounting Style: Surface Mount
• Construction: SMT Chip
• Case Style: Ceramic Chip
• Failure Rate: Not Required
• Wire Form: Not Required
• Product Length (mm): 2mm
• Product Depth (mm): 1.25mm
• Product Height (mm): 1.25mm
• Product Diameter (mm): Not Requiredmm
• Capacitance: .022uF
• Package / Case: 0805
• Lead Free Status / RoHS Status: Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
No.
10
11
12 Vibration
13
*1: The figure indicates typical specification. Please refer to individual specifications.
*2: Some of the parts are applicable in rated voltage x 150%. Please refer to individual specifications.
7
8
9
Continued from the preceding page.
Operational Life
External Visual
Physical Dimension
Resistance
to Solvents
Mechanical
Shock
Resistance to
Soldering Heat
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
AEC-Q200
Test Item
Appearance
Capacitance
Change
Q/D.F.
I.R.
Appearance
Capacitance
Change
Q/D.F.
I.R.
Appearance
Capacitance
Change
Q/D.F.
I.R.
Appearance
Capacitance
Change
Q/D.F.
I.R.
Appearance
Capacitance
Change
Q/D.F.
I.R.
Temperature Compensating Type
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within 3.0% or 0.30pF
(Whichever is larger)
30pFmin.: QU350
10pF and over, 30pF and below:
QU275+
10pFmax.: QU200+10C
C: Nominal Capacitance (pF)
More than 1,000M or 50 · F
(Whichever is smaller)
No defects or abnormalities
Within the specified dimensions
No marking defects
Within the specified tolerance
30pFmin.: QU1000
30pFmax.: QU400+20C
C: Nominal Capacitance (pF)
More than 10,000M or 500 · F
(Whichever is smaller)
No marking defects
Within the specified tolerance
30pFmin.: QU1000
30pFmax.: QU400+20C
C: Nominal Capacitance (pF)
More than 10,000M or 500 · F
(Whichever is smaller)
No defects or abnormalities
Within the specified tolerance
30pFmin.: QU1000
30pFmax.: QU400+20C
C: Nominal Capacitance (pF)
More than 10,000M or 500 · F
(Whichever is smaller)
The measured and observed characteristics should satisfy the
specifications in the following table.
No marking defects
Within the specified tolerance
30pFmin.: QU1000
30pFmax.: QU400+20C
C: Nominal Capacitance (pF)
More than 10,000M or 500 · F
(Whichever is smaller)
–
2
5
C
Specifications
Within 12.5%
W.V.: 25Vmin.: 0.035 max.
W.V.: 16V: 0.05 max.
W.V.: 25Vmin.: 0.025 max.
W.V.: 16V: 0.035 max.
W.V.: 25Vmin.: 0.025 max.
W.V.: 16V: 0.035 max.
W.V.: 25Vmin.: 0.025 max.
W.V.: 16V: 0.035 max.
W.V.: 25Vmin.: 0.025 max.
W.V.: 16V: 0.035 max.
High Dielectric Type
GCM Series Specification and Test Methods
*1
*1
*1
*1
*1
*1
*1
*1
*1
*1
Apply 200% of the rated voltage for 1000 12 hours at
125 3 C. Let sit for 24 2 hours at room temperature, then
measure. *2
The charge/discharge current is less than 50mA.
• Initial measurement for high dielectric constant type.
Apply 200% of the rated DC voltage for one hour at the maximum
operating temperature 3 C. Remove and let sit for 24 2 hours
at room temperature. Perform initial measurement. *2
Visual inspection
Using calipers
Per MIL-STD-202 Method 215
Three shocks in each direction should be applied along 3
mutually perpendicular axes of the test specimen (18 shocks).
The specified test pulse should be Half-sine and should have a
duration: 0.5ms, peak value: 1500g and velocity change: 4.7m/s.
Solder the capacitor to the test jig (glass epoxy board) in the
same manner and under the same conditions as (19). The
capacitor should be subjected to a simple harmonic motion
having a total amplitude of 1.5mm, the frequency being varied
uniformly between the approximate limits of 10 and 2000Hz. The
frequency range, from 10 to 2000Hz and return to 10Hz, should
be traversed in approximately 20 minutes. This motion should be
applied for 12 items in each 3 mutually perpendicular directions
(total of 36 times).
Immerse the capacitor in a eutectic solder solution at 260 5 C for
10 1 seconds. Let sit at room temperature for 24 2 hours, then
measure.
• Initial measurement for high dielectric constant type
Perform a heat treatment at 150
sit for 24 2 hours at room temperature.
Perform the initial measurement.
Specifications and Test Methods
Solvent 1: 1 part (by volume) of isopropyl alcohol
Solvent 2: Terpene defluxer
Solvent 3: 42 parts (by volume) of water
3 parts (by volume) of mineral spirits
1 part (by volume) of propylene glycol
monomethyl ether
1 part (by volume) of monoethanolamine
AEC-Q200 Test Method
Continued on the following page.
W0
Y10
C for one hour and then let
C03E.pdf
15
10.5.20
1