HSDL-3002-007 Avago Technologies US Inc., HSDL-3002-007 Datasheet
HSDL-3002-007
Specifications of HSDL-3002-007
Available stocks
Related parts for HSDL-3002-007
HSDL-3002-007 Summary of contents
Page 1
... IrDA® Data Compliant Low Power 115.2 kbit/s with Remote Control Transmission Infrared Transceiver Data Sheet Description The HSDL-3002 is a small form factor single enhanced infrared (IR) transceiver module that provides the combination of (1) interface between logic and IR signals for through-air, serial, half-duplex IR data link, and (2) IR remote control transmission operating at 940 nm for universal remote control applications ...
Page 2
... HSDL-3002 infrared transceiver module. You can contact them through your local sales representatives for additional details. Ordering Information Part Number Packaging Type HSDL-3002-007 Tape and Reel Marketing Information The unit is marked with a number “1” and “YWWLL” on the shield for front option. ...
Page 3
... Notes used to optimize the performance of the 870 nm LED, while R2 is the current limiting resistor for the 940 nm RC LED. 2. CX1 must be placed within 0 HSDL-3002 to obtain optimum noise immunity environment with noisy power supplies, supply rejection can be enhanced by including CX2 as shown in Figure 1. ...
Page 4
Transceiver I/O Truth Table Transceiver Mode Shutdown IrDA (TXD) Remote Control Input Active 0 Active 0 Active 0 Active 0 Active 0 Shutdown Don’t Care EI = In-Band Infrared Intensity at detector Notes: 4. In-Band EI 115.2 ...
Page 5
Electrical & Optical Specifications Specifications (Min. & Max. values) hold over the recommended operating conditions unless otherwise noted. Unspecified test conditions may be anywhere in their operating range. All typical values (Typ.) are with V otherwise noted. ...
Page 6
Notes in-band optical signal is a pulse/sequence where the peak wavelength, compliant with the IrDA Serial Infrared Physical Layer Link Specification. 8. For in band signals 2.4 kbps to 115.2 kbps where 3.6 W/cm 9. Latency is defined ...
Page 7
V OH 90% 50% 10 Figure 7. RXD output waveform. LED ON 90% 50% 10% LED OFF t r Figure 8. LED optical waveform. TXD LED t pw (MAX.) Figure 9. TXD “Stuck ON” protection. SD ...
Page 8
... HSDL-3002 Package Outline (with Integrated Shield) 0.885 1.35 2.65 1.25 2.95 1 COPLANARITY: +0.05 TO -0.15 0.80 Figure 12. Package outline dimension. 8 4.55 MOUNTING CENTER 9.10 ± 0.15 2.70 ± 0.15 2.60 5.80 1.55 R 1.50 R 1.10 3. 0.65 PITCH 1.00 0.50 ALL DIMENSIONS IN MILLIMETERS (mm). ...
Page 9
... HSDL-3002 Tape and Reel Dimensions 5.00° (MAX.) POLARITY PIN 8: GND 9.50 ± 0.10 PIN 1: VLED 0.40 ± 0.10 3.00 ± 0.10 MATERIAL OF CARRIER TAPE: CONDUCTIVE POLYSTYRENE MATERIAL OF COVER TAPE: PVC METHOD OF COVER: HEAT ACTIVATED ADHESIVE LABEL Figure 13. Tape and reel dimensions. ...
Page 10
... Moisture Proof Packaging All HSDL-3002 options are shipped in moisture proof package. Once opened, moisture absorption begins. This part is compliant to JEDEC Level 4. UNITS IN A SEALED MOISTURE-PROOF PACKAGE PACKAGE IS OPENED (UNSEALED) ENVIRONMENT LESS THAN 25°C, AND LESS THAN 60% RH? NO PACKAGE IS OPENED MORE THAN 72 HOURS ...
Page 11
... The cool down rate, R5, from the liquidus point of the solder (77 F) should not exceed -3 C per second maximum. This limitation is necessary to allow the PC board and HSDL-3602 castellation I/O pins to change dimensions evenly, putting minimal stresses on the HSDL- 3602 transceiver. ...
Page 12
Appendix A : SMT Assembly Application Note 1.0 Solder Pad, Mask and Metal Stencil STENCIL APERTURE SOLDER MASK Figure 16. Stencil and PCBA. 1.1 Recommended Land Pattern 2.65 0.715 1. 0.725 Figure 17. Land pattern. 12 ...
Page 13
Recommended Metal Solder Stencil Aperture It is recommended that only a 0.152 mm (0.006 inches 0.127 mm (0.005 inches) thick stencil be used for solder paste printing. This is to ensure adequate printed solder paste volume and ...
Page 14
Appendix B : PCB Layout Suggestion The following shows an example of a PCB layout that would result in good electrical and EMI perfor- mance. Things to note: 1. The ground plane should be continuous under the part, but should ...
Page 15
... LED to support universal remote control applications fully compliant to IrDA 1.4 low power specifica- tion from 9.6 kb/s to 115.2 kb/s, and supports most remote control codes. The design of the HSDL- Minimum Peak Pulse LED Current Conditions 350 mA Turn on 870 nm LED only TxD V ...
Page 16
... W/ Based on a typical irradiance of 0.075 and turning on both 870 nm and 940 nm LEDs, a typical link distance achieved. For a more exhaustive note on implementing remote control using HSDL-3002, please refer to the application note. ...
Page 17
... Figure 23. Window design diagram the figure below the width of the window the height of the window and Z is the distance from the HSDL-3002 to the back of the window. The distance from the center of the LED lens to the center of the photodiode lens 5.8 mm. The equations for ...
Page 18
Aperture Width (x, mm) Aperture Height (y, mm) Module Depth (z) mm Max. 0 15.73 1 16.89 2 18.04 3 19.19 4 20.35 5 21.5 6 22.66 7 23.81 8 24.97 9 26.12 APERTURE WIDTH (X) vs. MODULE DEPTH 30 ...
Page 19
Shape of the Window From an optics standpoint, the window should be flat. This ensures that the window will not alter either the radiation pattern of the LED, or the receive pattern of the photodiode. If the window must be ...
Page 20
For product information and a complete list of distributors, please go to our website: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Limited in the United States and other countries. Data subject to change. Copyright © ...