ERJM1WSF10MU Panasonic, ERJM1WSF10MU Datasheet - Page 5

• Manufacturer Part Number: ERJM1WSF10MU
• Description: RESISTOR, 2512, 0R01, 1%, 2W
• Manufacturer: Panasonic
• Series: ERJM1Wr

Specifications of ERJM1WSF10MU

• Resistance: 0.01ohm
• Resistance Tolerance: ± 1%
• Power Rating: 2W
• Resistor Element Material: Bare Metal
• Resistor Case Style: 2512
• No. Of Pins: 2
• Svhc: No
• Temperature Coefficient: ± 75ppm/°C
• Material, Element: Thick Film
• Package Type: 2512
• Power, Rating: 1 W
• Temperature, Operating, Maximum: 170 °C
• Temperature, Operating, Minimum: –55 °C
• Termination: SMT
• Tolerance: ±1 %
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Subject
Part No.
8.Enviromental Characteristics
9.Other Characteristics
10.Resistance Value Marking
11.Recommended Pad Layout
12.Manufacturing Country
High Temperature
Exposure
Temperature
Cycling
Humidity
(Steady State)
Load Life
Load Life in
Humidity
Surface
Temperature
Express resistance value on resin side.
ERJM1WT type
ERJM1WS type
Indonesia or Japan
3.4mm
Item
Item
Low Resistance Value Chip Resistor
ERJM1WT type
PANASONIC ELECTRONIC DEVICES CO.,LTD.
ERJM1W
3.1mm
2.2mm
less than 110deg.C up
1m :1M0 , 1.5m :1M5 , 2m :R002 , 3m :R003 , 4m :R004
R = +/-(1%+0.5m )
R = +/-(1%+0.5m )
R = +/-(1%+0.5m )
R = +/-(3%+0.5m )
R = +/-(3%+0.5m )
Specifications
Specifications
3m :3M0 , 4m :4M0 , 5m :5M0 , 6m :6M0
10m :10M , 15m :15M, 20m :20M
Circuit Pattern
(Cu etc.)
Resist
Pad
Resistors shall be exposed at 125+/-3deg.C
for 1000+48/-0 hours.
-55+/-3deg.C 30minutes
Normal temp. 30minutes
+125+/-3deg.C 30minutes
Resistors shall be exposed at 60+/-2deg.C
and 90 to 95% relative humidity in a humidity
test chamber for 1000+48/-0 hours.
Resistors shall be exposed at 70+/-2deg.C for
1000 +48/-0 hours.
rated voltage shall be applied intermittently for
1.5 hours ON,0.5 hours OFF.
Resistors shall be exposed at 60+/-2deg.C
and 90 to 95% relative humidity for
1000+48/-0 hours.
voltage shall be applied intermittently for 1.5
hours ON,0.5 hours OFF.
Resistor shall be mounted on aluminum
substrate (t = 1.0mm).
shall be applied.
center of resistor is measured.
Test Methods(Based on JIS-C5201)
Example
ERJM1WS type
Test methods
4.2mm
The temperature rise at the
During this time the rated
During this time the
2.1mm
A power of 1.0W
Spec. No.
5 cycles
151-RJM-E01MM
3.4mm
10 -
5