ERJM1WSF10MU Panasonic, ERJM1WSF10MU Datasheet

Page 1

... ERJM1WS [.252+/-.010] 2.Power Derating Curve Category Temperature Range (Operating Temperature Range): -55 to +170 deg.C 120 100 -55 -40 PANASONIC ELECTRONIC DEVICES CO.,LTD. ERJM1WS type Terminal Alloy Metal Metal W T 3.20+/-0.25 0.80+/-0.30 [.126+/-.010] [.031+/-.012] ...

Page 2

... The surface of terminal is covered by the plating. And the plating is Construction hard to fade, then don't have unevenness, flaw, pinhole and discoloration. 3. The terminal is connected with resistive plate certainly. PANASONIC ELECTRONIC DEVICES CO.,LTD. Specifications When you use one at ambient temperature over 2.0W 70deg.C, the load power shall be reduced as (70deg ...

Page 3

... ERJM1WS type ≥ 5mΩ Intermittent ∆R = +/-(5%+0.5mΩ) Overload No evidence of flash over, mechanical Dielectric damage, arcing or insulation Withstanding breakdown. Insulation Resistance PANASONIC ELECTRONIC DEVICES CO.,LTD 1.06×10 5 Top terminal × × Test Methods(Based on JIS - C5201) Measuring current: 1A 20deg.C 65%RH -6 +/-75×10 /deg ...

Page 4

... Terminal Strength Without distinct deformation Bending Strength in appearance Solderability min. 95% coverage Resistance to ∆R = +/-(5%+0.5mΩ) Soldering Heat PANASONIC ELECTRONIC DEVICES CO.,LTD. Test Methods(Based on JIS-C5201) Copper plate 0.4mm Pull speed Fixed min. 4.9N Substrate : Glass Epoxy (t=1.6mm) Span : 90mm Bending Distance : 2mm (10 seconds) ...

Page 5

... Capper Thickness:70 micro meter 9.Resistance Value Marking Express resistance value on resin side. ERJM1WT type ERJM1WS type 5mΩ:5M0 , 6mΩ:6M0 ,10mΩ:10M PANASONIC ELECTRONIC DEVICES CO.,LTD. Test Methods(Based on JIS-C5201) Resistors shall be exposed at 125+/-3deg.C for 1000+48/-0 hours. -55+/-3deg.C 30minutes Normal temp. 30minutes +125+/-3deg ...

Page 6

... Subject Low Resistance Value Chip Resistor Part No. ERJM1W 10.Recommended Pad Layout ERJM1WT type 3.1mm 3.4mm 2.2mm 11.Manufacturing Country Indonesia PANASONIC ELECTRONIC DEVICES CO.,LTD. ERJM1WS type 2.1mm Circuit Pattern (Cu etc.) Pad Resist 4.2mm Spec. No. 151-RJM-E2W00A 3.4mm ...

Page 7

... PANASONIC ELECTRONIC DEVICES CO.,LTD. Spec. No. 151-RJM-E2W00A ...

Page 8

... Chemical substances. 4 All the materials used in this part contain no brominated materials of PBBOs or PBBs as the flame-retardant you need the notice by letter of "A preliminary judgement on the Laws of Japan foreign exchange and Foreign Trade control", be sure to let us know. PANASONIC ELECTRONIC DEVICES CO.,LTD. Spec. No. 151-RJM-E2W00A ...

Page 9

... Note the followings in case of using soldering iron for replacement. (1) The tip temperature should be less than 350 °C for the period within 3 s for each terminal. (2) The soldering iron tip should not touch the product directly. PANASONIC ELECTRONIC DEVICES CO.,LTD. Peak Preheatin Main heating ...

Page 10

... Carrier Tape Dimensions T φD0 φ 3.60+/-0.20 6.90+/-0.20 [.141+/-.008] [.272+/-.008 2.00+/-0.05 4.00+/-0.10 [.079+/-.002] [.157+/-.004] PANASONIC ELECTRONIC DEVICES CO.,LTD. 13.0 +/- 1.0 15.4 +/- 2 Sprocket Hole B Compartment Chip Resistor 12.0+/-0.30 5.50+/-0.05 [.472+/-.012] [.217+/-.002] φ ...

Page 11

... Part Name('Fixed metal plate flat chip resistor' following part name on invoice) 2) Part Number 3) Quantity 6) Manufacturing Country • Packaging Box 1) Part Number 2) Quantity 3) Maker Name PANASONIC ELECTRONIC DEVICES CO.,LTD. Peeling Direction 10° Top Tape Tape Marking 4) Lot Number 5) Maker Name Spec. No. ...