B51-328-3188220 ITT SEALECTRO, B51-328-3188220 Datasheet - Page 44

• Manufacturer Part Number: B51-328-3188220
• Description: RF/COAXIAL, SMB PLUG, R/A, 50OHM, CRIMP
• Manufacturer: ITT SEALECTRO

Specifications of B51-328-3188220

• Body Style: Right Angle Plug
• Coaxial Termination: Crimp
• Rg Cable Type: RG-174, 316
• Contact Material: Beryllium Copper
• Contact Plating: Gold
• Connector Type: SMB Coaxial
• Impedance: 50ohm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

A A I I - - 1 1 2 2 8 8 & & A A I I - - 6 6 6 6 3 3
Cannon 50 Ohm Connectors
STEP 14
STEP 1
STEP 2
STEP 4
STEP 7
STEP 8
STEP 3
STEP 12
SHRINKABLE
TUBING
HEAT
D
B
S S S S M M B B / / S S S S M M C C S S t t r r a a i i g g h h t t C C o o n n n n e e c c t t o o r r s s , , C C r r i i m m p p T T y y p p e e f f o o r r
B B r r a a i i d d e e d d C C a a b b l l e e
SURFACE
SURFACE
FERRULE
CRIMP
C
A
A
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. Place a small solder preform made from 0,26 - 0,31 (.010 - .012) dia.
11. Place rear insulator over center conductor. When insulator has counterbore,
12. Assemble contact onto center conductor, heat to make solder connection.
13. Solder should be visible at inspection hole, if excess solder runs from
14. Screw on the front body and tighten to a torque of 0.14Nm (20 in. ozs)
AI-128 for all other conductor sizes
Slide heat shrinkable tubing and ferrule on to cable.
Trim cable to dimensions shown:
Slide rear body over dielectric and under the braid until braid is flush with
flange. N.B. When using cable with inflexible jackets it is permissible to
make two 3,00 (.118) long longitudinal slits in the outer jacket.
Slide ferrule over exposed braid up to hex. flange.
Crimp using Cannon’s Crimp Tool and suitable Die Set (see table). Ensure
ferrule is held close to hex. flange.
Slide heat shrinkable tubing over crimp and heat shrink into place using hot
air gun. Air temperature should be approximately 125˚C.
Trim dielectric flush with surface “A” on body using a sharp knife. Take care
not to nick center conductor.
Trim center conductor as shown.
Tin center conductor (do not allow solder to touch end of body or dielectric).
(28 swg) multi-core solder in rear of contact.
the contact fits into the counterbore.
Do not allow solder to protrude outside spill hole.
inspection hole, remove with sharp blade taking care not to damage plating.
Only common cable retention features are shown in detail.
Various body configurations can apply.
AI-128 for center conductors ø 0.51 (.020)
Assembly Instruction No.
Cable Numbers
REAR BODY
RG196/U
RG316/U
RD316
44
AI-663
Cable Code
3196
3188
3875
INSULATOR
REAR
ASSEMBLY INSTRUCTIONS
Specifications and dimensions subject to change
2,67 (.105)
3,25 (.128)
3,84 (.151)
Die Size
6,86 (.270)
6,76 (.266)
7,54 (.297)
CONTACT
B
Dimensions shown in mm (inch)
2,29 (.090)
2,29 (.090)
3,05 (.120)
T1025/9
K29263
K29263
Die Set
www.ittcannon.com
FRONT
BODY
C
10,41 (.410)
10,31 (.406)
9,53 (.375)
D