MC-NOVE MULTICOMP, MC-NOVE Datasheet - Page 3

• Manufacturer Part Number: MC-NOVE
• Description: Arduino Duemilanove Based Board W/ ATMEGA328
• Manufacturer: MULTICOMP

Specifications of MC-NOVE

• Silicon Manufacturer: Atmel
• Core Architecture: AVR
• Features: 16MHz Crystal Oscillator, USB Connection, ICSP Header
• Kit Contents: Development Board Only
• Silicon Family Name: Atmega
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Programming
The MC-NOVE can be programmed with the Arduino™ software (download). Select "Arduino™ Duemilanove w/ ATmega328" from
the Tools > Board menu. For details, see the reference and tutorials.
The ATmega328 on the MC-NOVE comes pre-burned with a bootloader that allows you to upload new code to it without the use of
an external hardware programmer. It communicates using the original STK500 protocol (reference, C header files).
You can also bypass the bootloader and program the microcontroller through the ICSP (In-Circuit Serial Programming) header; see
these instructions for details.
Automatic (Software) Reset
Rather than requiring a physical press of the reset button before an upload, the MC-NOVE is designed in a way that allows it to be
reset by software running on a connected computer. One of the hardware flow control lines (DTR) of the FT232RL is connected to
the reset line of the ATmega328 via a 100 nanofarad capacitor. When this line is asserted (taken low), the reset line drops long
enough to reset the chip. The Arduino™ software uses this capability to allow you to upload code by simply pressing the upload
button in the Arduino™ environment. This means that the bootloader can have a shorter timeout, as the lowering of DTR can be
well-coordinated with the start of the upload.
This setup has other implications. When the MC-NOVE is connected to either a computer running Mac OS X or Linux, it resets each
time a connection is made to it from software (via USB). For the following half-second or so, the bootloader is running on the MC-
NOVE. While it is programmed to ignore malformed data (i.e. anything besides an upload of new code), it will intercept the first few
bytes of data sent to the board after a connection is opened. If a sketch running on the board receives one-time configuration or
other data when it first starts, make sure that the software with which it communicates waits a second after opening the connection
and before sending this data.
The MC-NOVE contains a trace that can be cut to disable the auto-reset. The pads on either side of the trace can be soldered
together to re-enable it. It's labelled "RESET-EN". You may also be able to disable the auto-reset by connecting a 110 ohm resistor
from 5V to the reset line; see this forum thread for details.
USB Overcurrent Protection
The MC-NOVE has a resettable polyfuse that protects your computer's USB ports from shorts and overcurrent. Although most
computers provide their own internal protection, the fuse provides an extra layer of protection. If more than 500 mA is applied to the
USB port, the fuse will automatically break the connection until the short or overload is removed.
Physical Characteristics
The maximum length and width of the MC-NOVE PCB are 2.7 and 2.1 inches respectively, with the USB connector and power jack
extending beyond the former dimension. Three screw holes allow the board to be attached to a surface or case. Note that the
distance between digital pins 7 and 8 is 160 mil (0.16"), not an even multiple of the 100 mil spacing of the other pins.
Schematic & Reference Design
EAGLE files: arduino-duemilanove-reference-design.zip
Schematic: arduino-duemilanove-schematic.pdf
MC-NOVE
Arduino™ Duemilanove Compatible Development Board
http://www.farnell.com
http://www.newark.com
http://www.cpc.co.uk
Page <3>
28/05/10 V1.1