SK-96320-80PMC Fujitsu, SK-96320-80PMC Datasheet

Page 1

... Fujitsu Microelectronics Europe User Guide FMEMCU-UG-960010-12 F²MC-16FX FAMILY EVALUATION BOARD SK-96320-80PMC USER GUIDE ...

Page 2

... Revision History Date 06.07.2007 V1.0, HWe/DGo, First Release 08.02.2008 V1.1, HWe, China-RoHS regulation added 01.04.2008 V1.2, HWe, Chapter 5.7 corrected (Pin 55 - 57) This document contains 34 pages. FMEMCU-UG-960010-12 SK-96320-80PMC User Guide Revision History Issue - 2 - © Fujitsu Microelectronics Europe GmbH ...

Page 3

... Warranty and Disclaimer To the maximum extent permitted by applicable law, Fujitsu Microelectronics Europe GmbH restricts its warranties and its liability for the SK-96320-80PMC Board and all its deliverables (eg. software include or header files, application examples, target boards, evaluation boards, engineering samples of IC’s etc.), its performance and any consequential damages, on the use of the Product in ...

Page 4

... UART”A”, UART”B” connector (X3, X5)................................................................. 25 5.4 LIN”A”, LIN”B” Interface connector (X6, X8) .......................................................... 26 5.5 CAN”A”, CAN”B” Interface connector (X10, X11)................................................... 26 5.6 USER-LEDs & optional LC-Display ....................................................................... 26 FMEMCU-UG-960010-12 SK-96320-80PMC User Guide Contents - 4 - © Fujitsu Microelectronics Europe GmbH ...

Page 5

... VG96 connector (X4)............................................................................................. 27 6 SILK-PLOT OF THE BOARD ........................................................................................ 28 7 REVISION AND ERROR LIST ....................................................................................... 29 8 RELATED PRODUCTS ................................................................................................. 30 9 INFORMATION IN THE WWW....................................................................................... 31 10 CHINA-ROHS REGULATION ........................................................................................ 32 11 RECYCLING .................................................................................................................. 34 © Fujitsu Microelectronics Europe GmbH SK-96320-80PMC User Guide Contents - 5 - FMEMCU-UG-960010-12 ...

Page 6

... Overview 1.1 Abstract The SK-96320-80PMC is a multifunctional evaluation board for the Fujitsu 16-bit Flash microcontroller series MB96320. It can be used stand-alone for software development and testing simple target board to work with the emulator system. The board allows the designer immediately to start software development before his own final target system is available ...

Page 7

... General Description The SK-96320-80PMC supports the 16-bit Flash microcontroller MB96320 Series. It can be used as a stand-alone evaluation board target board for the emulator debugger. The evaluation board supports the following package: FPT-80P-M21. The board is supplied with a socketed 4 MHz crystal as main oscillation source. Using the internal PLL of the KC, higher internal clock rates MHz can be achieved ...

Page 8

... If the board is used as an emulator target board, the microcontroller must be removed from the socket and the corresponding probe cable has to be mounted: Series V-Chip MB96320 MB96V300B FMEMCU-UG-960010-12 SK-96320-80PMC User Guide Chapter 1 Overview Probe cable NQ-Pack MB2198-505 NQPACK080SD- © Fujitsu Microelectronics Europe GmbH ...

Page 9

... When turning on the system, be sure to use the following power-up sequence: 1. Power up the emulator main unit (MB2198-01) 2. Power up the adapter board (MB2198-500) 3. Power up the target board (SK-96320-80PMC) To turn off the system, switch off the components in reverse order, beginning with the target board. ...

Page 10

... TLE6259(2-3)/TLE7259(1-2) “WAKE” JP43 Power JP44 LIN VBat A JP45 LIN VBat B JP46 SDA0 Pull-Up JP47 SCL0 Pull-Up FMEMCU-UG-960010-12 SK-96320-80PMC User Guide Chapter 2 Installation Type Jumper 2 pin Jumper 2 pin Jumper 3 pin Jumper 3 pin Jumper 3 pin Jumper 2 pin Solder JP 3 pin Jumper 2 pin Jumper 2 pin ...

Page 11

... UART UART Solder Jumper Std. Jumper © Fujitsu Microelectronics Europe GmbH SK-96320-80PMC User Guide Chapter 2 Installation LIN B LIN CAN CAN FMEMCU-UG-960010-12 ...

Page 12

... For more detailed information please check the Hardware-Manual of the microcontroller. DIP switch S2/1 (MD0) S2/2 (MD1) S2/3 (MD2) S2/4 Dip-Switch S2 (run mode) FMEMCU-UG-960010-12 SK-96320-80PMC User Guide Chapter 3 Jumpers and Switches Setting Logical value ON (closed) OFF (open) ON (closed) OFF (open) ON (closed) OFF (open) ...

Page 13

... Closed (VBAT_A) Open JP45 Closed (VBAT_B) Open © Fujitsu Microelectronics Europe GmbH SK-96320-80PMC User Guide Chapter 3 Jumpers and Switches Description MCU / Peripherals @ 5V MCU / Peripherals @ 3.3V Power supply Vcc connected to VDD5 Power supply Vcc not connected to VDD5 The board is switched on The board is switched off ...

Page 14

... If JP11 and JP15 are open, the user has to supply an adequate analog voltage supply (AVcc and AVss) to the A/D-converter. If JP13 is open, the resistors R11 and R23 define AVRH. By default the resistors R11 and R23 are not mounted on the board. FMEMCU-UG-960010-12 SK-96320-80PMC User Guide Chapter 3 Jumpers and Switches Description Closed AVcc is connected to Vcc ...

Page 15

... JP34 (X1A, P41) 2-3 Default: JP41: 1-2, JP34: 1-2 By default, the 32 kHz-subclock-crystal is connected to the microcontroller. © Fujitsu Microelectronics Europe GmbH SK-96320-80PMC User Guide Chapter 3 Jumpers and Switches Pin-out JP41: Description Pin 24 is connected to the 32kHz Subclock (X0A) Pin 24 is used as P4_0 and is connected to X4-B10 ...

Page 16

... Open By default, UART3 is connected to UART”B”. UART “B” can be used for serial asynchronous Flash programming. FMEMCU-UG-960010-12 SK-96320-80PMC User Guide Chapter 3 Jumpers and Switches Description SIN2 of the MCU is connected to UART”A” SIN2 of the MCU is not connected to UART”A” ...

Page 17

... Open Closed JP44 (VBAT_A) Open JP36 (WAKE) By default, the LIN”A”-interface is not connected to a UART. © Fujitsu Microelectronics Europe GmbH SK-96320-80PMC User Guide Chapter 3 Jumpers and Switches Description LIN-transceiver is enabled LIN-transceiver is disabled LIN Master-mode LIN Slave-mode SIN7 of the MCU is connected to LIN”A” ...

Page 18

... Jumper Setting JP25 (CAN”A”TX) closed JP26 (CAN”A”RX) closed JP19 (VCC CAN A) FMEMCU-UG-960010-12 SK-96320-80PMC User Guide Chapter 3 Jumpers and Switches Description LIN-transceiver is enabled LIN-transceiver is disabled LIN Master-mode LIN Slave-mode SIN8 of the MCU is connected to LIN”B” SIN8 of the MCU is not connected to LIN”B” ...

Page 19

... For normal operation the C-pin must be connected to two capacitors. For test purposes you can disconnect these two capacitors. Jumper Setting closed JP40 (C-Pin) © Fujitsu Microelectronics Europe GmbH SK-96320-80PMC User Guide Chapter 3 Jumpers and Switches Description TX2 of MCU is connected to CAN”B” RX2 of MCU is connected to CAN”B” 1-2 CAN B VCC is set to 5V ...

Page 20

... If JP35 (Polarity) is set, JP4 and either JP3 or JP5 have to be set, too. If the reset LED is steadily on, check the power supply input voltage and the settings for the reset-generation by UART. FMEMCU-UG-960010-12 SK-96320-80PMC User Guide Chapter 3 Jumpers and Switches Description 1-2 DTR of UART”A” is selected 2-3 RTS of UART” ...

Page 21

... Open Default: JP12, JP14, JP16, JP20, JP23, JP24 = Closed By default, all push-buttons as well as the reset circuit are connected to the microcontroller. © Fujitsu Microelectronics Europe GmbH SK-96320-80PMC User Guide Chapter 3 Jumpers and Switches Description Pin 74 (INT0) of the MCU is connected to “SW1” No connection to the microcontroller Pin 77 (INT1) of the MCU is connected to “ ...

Page 22

... Connect the Evaluation Board UART”A” or UART”B” to your serial PC communication port. A straight 1:1 cable connection has to be used. 3. Check the Jumper-settings according to the UART as described in chapter 3.5 4. Configure the mode: Dip-Switch S2 (Flash mode) 5. Power on the board FMEMCU-UG-960010-12 SK-96320-80PMC User Guide MD0 MD1 MD2 nc ON OFF © ...

Page 23

... After programming the Flash-ROM, switch off the power supply and set back the mode according to the usage of the application, e.g.: MD0 MD1 MD2 nc Dip-Switch S2 (Run mode) 1 10. Power on the board. The user application is started directly. © Fujitsu Microelectronics Europe GmbH SK-96320-80PMC User Guide ON OFF FMEMCU-UG-960010-12 ...

Page 24

... GALEP-4 from www.conitec.de. This tool is not available for free. A dedicated Flash programming socket (X4) is provided on the evaluation-board for direct connection to this programmer. X17: Flash programming socket Figure 4-2: Flash Programming Socket FMEMCU-UG-960010-12 SK-96320-80PMC User Guide nc P00_1 MD0 3 4 nc. RSTX 5 ...

Page 25

... TXD is the transmit output, RXD is the receive input. The DTR or RTS signal can be used to generate a reset. Please use a 1:1 cable for PC-connection. © Fujitsu Microelectronics Europe GmbH SK-96320-80PMC User Guide Chapter 5 Connectors Shield is connected to positive voltage supply Center is connected to ground (GND) MCU Pins 1 – ...

Page 26

... Instead of the user-LEDs an alphanumeric LC-Display (optional) can be connected. The following control signals are provided LCD LED MCU Port 06_7 06_6 06_5 06_4 FMEMCU-UG-960010-12 SK-96320-80PMC User Guide Chapter 5 Connectors 5 9 Connectors X6, X8: Connector X10 06_3 06_2 06_1 06_0 - 26 - © Fujitsu Microelectronics Europe GmbH ...

Page 27

... P01_4 45 16B P01_5 46 16C P01_6 47 17A P01_7 48 17B P09_2 49 17C P09_3 50 18A P02_0 © Fujitsu Microelectronics Europe GmbH SK-96320-80PMC User Guide Chapter 5 Connectors Evaboard MCU X4 51 AVSS (JP15) 18B 52 AVRH 18C 53 LED D3 19A 54 LED D4 19B 55 LED D5 19C LED D6 56 20A ...

Page 28

... Pin 1 Pin 2 X1 Pin 40 Pin 39 X12 Power- Jack CAN”B” X11 SW1 CAN”A” X10 FMEMCU-UG-960010-12 SK-96320-80PMC User Guide Chapter 6 Silk-Plot of the Board VG96-male MCU 96F326 4MHz optional: LCD SW3 SW4 SW5 SW2 LIN”A” LIN”B” X8 ...

Page 29

... Revisions – Errors 18.04.2007 New document 18.04.2007 EMDC Design Spec Change < RSTx at pin 57 (former pin 55) < Hand wire RST to pin 57 (required for PCB V1.0) © Fujitsu Microelectronics Europe GmbH SK-96320-80PMC User Guide Chapter 7 Revision and Error List - 29 - Author Rev HWe/DGo 1.0 HWe 1 ...

Page 30

... MB2198-500 < NQPACK080SD-ND < HQPACK080SD < MB96320 Series < MB96V300B < MB96F326RS < MB96F326RW FMEMCU-UG-960010-12 SK-96320-80PMC User Guide Chapter 8 Related Products Evaluation board for the MB96F326 MCU in FPT-80P-M21 package Probe cable Emulator debugger main unit Emulation Pod / Adapter board Socket for package FPT-80P-M21 (Tokyo Eletech Corp. http://www.tetc.co.jp/) ...

Page 31

... Datasheets and Hardware Manuals, Support Tools (Hard- and Software) http://mcu.emea.fujitsu.com/ Power Management Products http://www.fujitsu.com/emea/services/microelectronics/powerman/ Media Products: SAW filters, acoustic resonators and VCOs http://www.fujitsu.com/emea/services/microelectronics/saw/ For more information about FUJITSU MICROELECTRONICS http://www.fujitsu.com/emea/services/microelectronics/ © Fujitsu Microelectronics Europe GmbH SK-96320-80PMC User Guide Chapter 9 Information in the WWW - 31 - FMEMCU-UG-960010-12 ...

Page 32

... FMEMCU-UG-960010-12 SK-96320-80PMC User Guide Chapter 10 China-RoHS regulation Explanation of Pollution Control Label SJ/T11363-2006 - 32 - © ...

Page 33

... X: Indicates that this toxic or hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in SJ/T11363-2006. • Data listed in the table represents best information available at the time of publication © Fujitsu Microelectronics Europe GmbH SK-96320-80PMC User Guide Chapter 10 China-RoHS regulation Hazardous substances name (Hg) (Cd) ...

Page 34

... According to the European WEEE-Directive and its implementation into national laws we take this device back. For disposal please send the device to the following address: Fujitsu Microelectronics Europe GmbH Warehouse/Disposal Monzastraße 4a 63225 Langen FMEMCU-UG-960010-12 SK-96320-80PMC User Guide Chapter 11 Recycling - 34 - © Fujitsu Microelectronics Europe GmbH ...