AD9910/PCBZ Analog Devices Inc, AD9910/PCBZ Datasheet - Page 15

• Manufacturer Part Number: AD9910/PCBZ
• Description: Direct Digital Synthesis Evaluation Board
• Manufacturer: Analog Devices Inc
• Series: AgileRF™r

Specifications of AD9910/PCBZ

• Silicon Manufacturer: Analog Devices
• Application Sub Type: Direct Digital Synthesizer
• Kit Application Type: Clock & Timing
• Silicon Core Number: AD9910
• Kit Contents: Board
• Design Resources: Synchronizing Multiple AD9910 1 GSPS Direct Digital Synthesizers (CN0121)
• Main Purpose: Timing, Direct Digital Synthesis (DDS)
• Embedded: No
• Utilized Ic / Part: AD9910
• Primary Attributes: 14-Bit DAC, 32-Bit Tuning Word Width
• Secondary Attributes: 1GHz, Graphical User Interface
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: Q3335404

The RAM I/O Window allows you to easily interface RAM data
into the AD9910. Use the RAM Data File box to locate the
RAM file on the PC. Use the Data Format drop-down box to
select the file format. The options are: RAW Binary, RAW Hex,
and RAW Decimal. Use the Load File button to transfer the
data to the AD9910. The Read RAM to File button allows you
to read the data from the RAM to a file in the same folder as the
evaluation board software. The Output Data Format allows
you to select the format of the output file. The options are:
RAW Binary, RAW Hex, and RAW Decimal. Use the Open
File in Notepad check box to view the file immediately.
DEBUG
To access the Debug window, select Debug Window from the
View drop-down menu (see Figure 10).
The Debug window gives you complete direct access to the
register map as well as control of many external pins. The Debug
window is intended for debugging issues with the AD9910. It
can be used for all programming, but is not user-friendly; this
may result in improper programming of reserved bits.
Figure 15. Debug Window
Rev. 0 | Page 15 of 20
DUT Signals (PA)
The ISFC, ExtPwrDwn, Reset DUT, I/O Reset, and CSB check
boxes control the pins to which they correspond. All of these
functions are available elsewhere in the software. A check in the
box means that the pin is in its active state. Note that this does
not mean that the pin is logic high or low. This is determined by
the active state on that pin. See the AD9910 data sheet for
information about external pins. The Flash and USB_Status
check boxes are used to control the two LEDs on the AD9910
evaluation board.
DUT Signals (PE)
The REGUD_EN, DRCTL, DRHOLD, REGUD, OSK, P3, P2,
and P1 check boxes control their selected pins. REGUD issues an
I/O update to the device under test (DUT), whereas REGUD_EN
allows the software to control the I/O_UPDATE pin. P3, P2,
and P1 control the profile register pins. See the AD9910 data
sheet for the logic to control the profiles via the external pins.
DUT Signals (CTL)
The SCLK (serial clock pin) check box is used to synchronize
data to and from the AD9910, and to run the internal state
machines. This window allows you to toggle the external pin.
DUT Flags (PD)
The PLL Lock, Sync Sample Error, RAM Sweep Over, and
Digital Ramp Over alerts indicate an active state on each of
those external pins. See the AD9910 data sheet for descriptions
of the active state of each pin.
Serial I/O
The Serial I/O area allows direct access to the register map. The
Reg Addr drop-down box allows you to select the register of
interest. The bit numbers are shown above each byte in the register.
The maximum size of any given register is eight bytes. For registers
that are smaller, the unavailable bytes are grayed out. You can
type the register values in either binary or hexadecimal format.
The Serial Port Status area displays alerts for the serial
operating mode of the AD9910, LSB First or 3-Wire Mode.
Auto Apply
Note that when the Auto Apply check boxes in the DUT
Signals (PA), DUT Signals (PE), and DUT Signals (CTL) areas
are selected, the action is automatically taken without the need
to click the Apply button.
AD9910/PCBZ