AFCT-721XPDZ Avago Technologies US Inc., AFCT-721XPDZ Datasheet - Page 4

• Manufacturer Part Number: AFCT-721XPDZ
• Description: NORA XFP 10km 10GFC/10GbE 0-70
• Manufacturer: Avago Technologies US Inc.
• Series: -r

Specifications of AFCT-721XPDZ

• Data Rate: 10.625Gbps
• Wavelength: 1310nm
• Applications: General Purpose
• Voltage - Supply: 3.135 V ~ 3.465 V
• Connector Type: LC Duplex
• Mounting Type: Panel Mount
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Table 1. Electrical Pin Definitions
Notes:
1. Module ground pins Gnd are isolated from the module case and chassis ground within the module.
2. Open Collector should be pulled up with 4.7KW to 10KW to a voltage between 3.15 V and 3.6 V on the host board.
3. RefCLK+/- are internally terminated (50W)
4. Pulled up to Vcc3 via 4.7-10KW resistor inside the module

Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Name
GND
V
Mod-Desel
Interrupt
TX_DIS
V
GND
V
V
SCL
SDA
Mod_Abs
Mod_NR
RX_LOS
GND
GND
RD-
RD+
GND
V
P_Down/RST
V
GND
RefCLK+
RefCLK-
GND
GND
TD-
TD+
GND
EE
CC
CC
CC
CC
CC
5
5
3
3
2
2
Logic
LVTTL-I
LVTTL-O
LVTTL-I
LVTTL-I
LVTTL-I/O
LVTTL-O
LVTTL-O
LVTTL-O
CML-O
CML-O
LVTTL-I
PECL-I
PECL-I
CML-I
CML-I
Function/Description
Module Ground
-5.2 V power supply. (Not Used)
Module De-select; When held low allows the module to respond to 2-wire Se-
rial interface commands
Interrupt; Indicates presence of an important condition which can be readover
the serial 2-wire interface
Transmitter Disable; Transmitter Laser Source Turned Off
5 V power supply. (Not Used)
Module Ground
+3.3 V Power Supply
+3.3 V Power Supply
Two Wire Interface Clock
Two Wire Interface Data Line
LVTTL-O Mod_Abs Indicates Module is not present. Grounded in the Module
Module Not Ready; Indicating Module Operational Fault
Receiver Loss Of Signal Indicator
Module Ground
Module Ground
Receiver Inverted Data Output
Receiver Non-Inverted Data Output
Module Ground
+1.8 V Power Supply. (Not Used)
Power down: When high, the module is put into a lower power mode. Serial
interface is functional in the low power mode. Reset: The falling edge initiates
a complete reset of the module including the serial Interface, equivalent to a
power cycle.
+1.8 V Power Supply. (Not Used)
Module Ground
Reference Clock Non-Inverted Input, AC coupled on the host board (Not Used)
Reference Clock Inverted Input, AC coupled on the host board (Not Used)
Module Ground
Module Ground
Transmitter Inverted Data Input
Transmitter Non-Inverted Data Input
Module Ground
Notes
1
4
2
4
1
2
2
2
2
2
1
1
1
4
1
3
3
1
1
1