AFCT-701ASDZ Avago Technologies US Inc., AFCT-701ASDZ Datasheet
AFCT-701ASDZ
Specifications of AFCT-701ASDZ
Available stocks
Related parts for AFCT-701ASDZ
AFCT-701ASDZ Summary of contents
Page 1
... SFP+ Transceiver for SMF 10km links Case temperature 0-85 qC Data Sheet Description The Avago AFCT-701ASDZ transceiver is part of a fam- ily of SFP+ products. This transceiver utilizes Avago’s 1310nm DFB and PIN Detector technology to provide an IEEE 10Gb Ethernet design compliant with the 10GBASE- LR standard ...
Page 2
... For optical links, the ability to identify a fault at a local device, remote device or cable plant is crucial to speed- ing service of an installation. AFCT-701ASDZ real-time monitors of Tx_Bias, Tx_Power, Vcc, Temperature and Rx_Power can be used to assess local transceiver current operating conditions ...
Page 3
... This Tx laser driver circuit regulates the optical power at a level within the specified range. Transmit Disable (TX_DISABLE) The AFCT-701ASDZ accepts an LVTTL compatible trans- mit disable control signal input which shuts down the transmitter optical output. A high signal implements this function while a low signal allows normal transceiver op- eration ...
Page 4
... AFCT-701ASDZ. All mechanical adjustments are made at the factory prior to shipment. Tampering with, modifying, misusing or improperly han- dling the AFCT-701ASDZ will void the product warranty. It may also result in improper operation and possibly overstress the laser source. Performance degrada tion or device failure may result ...
Page 5
... States, CENELEC EN55022 (CISPR 22) in Europe and VCCI in Japan. The AFCT-701ASDZ enables equipment com- pliance to these standards detailed in Table 1. The metal housing and shielded design of the AFCT-701ASDZ min- imizes the EMI challenge facing the equipment designer. For superior EMI performance it is recommended that equipment designs utilize SFP+ cages per SFF 8432 ...
Page 6
Table 1. Regulatory Compliance Feature Test Method Electrostatic Discharge (ESD) MIL-STD883C Method 3015.4 to the Electrical Contacts JEDEC DESD22-A11-4-B Electrostatic Discharge (ESD) IEC 61000-4-2 to the Duplex LC Receptacle Life Traffic ESD Immunity IEC 61000-4-2 Life Traffic ESD Immunity IEC ...
Page 7
TX_DISABLE TX_FAULT SERDES IC PROTOCOL IC LOSS OF SIGNAL RS0 RS1 MODULE DETECT SCL SDA Figure 2. Typical application configuration 7 4 kΩ 4.7uH Host DCR=0.15 Vcc 0 .1μF 4.7uH . DCR=0.15 0 .1μF 4 ...
Page 8
Table 2. Contact Description Contact Symbol Function/Description 1 VeeT Transmitter Signal Ground 2 TX_FAULT Transmitter Fault (LVTTL-O) – High indicates a fault condition 3 TX_DISABLE Transmitter Disable (LVTTL-I) – High or open disables the transmitter 4 SDA Two Wire Serial ...
Page 9
Table 3. Absolute Maximum Ratings Stress in excess of any of the individual Absolute Maximum Ratings can cause immediate catastrophic damage to the module even if all other parameters are within Recommended Operating Conditions. It should not be assumed that ...
Page 10
Table 5. Low Speed Signal Electrical Characteristics The following characteristics are defined over the Recommended Operating Conditions unless otherwise noted. Typical values are for Tc = 40°C. VccT and VccR = 3.3 V. Parameter Module Supply Current Power Dissipation TX_FAULT, ...
Page 11
NORMALIZED TIME (UNIT INTERVAL) Figure 4a. Receiver Electrical Optical Eye Mask Definition Table 7. Two-Wire Interface Electrical Characteristics Parameter Symbol Host Vcc Range VccHTWI SCL and SDA SCL ...
Page 12
Table 8. Optical Specifications The following characteristics are defined over the Recommended Operating Conditions unless otherwise noted. Parameter Transmitter Laser OMA output power Laser mean output power Laser off power Extinction ratio Transmitter and dispersion penalty (TDP) Center Wavelength Side ...
Page 13
Table 9. Control Functions: Low Speed Signals Timing Characteristics The following characteristics are defined over the Recommended Operating Conditions unless otherwise noted. Parameter TX_DISABLE Assert Time TX_DISABLE Negate Time Time to initialize, including reset of TX_FAULT TX_FAULT Assert Time TX_DISABLE ...
Page 14
Table 11. Transceiver Digital Diagnostic Monitor (Real Time Sense) Characteristics The following characteristics are defined over the Recommended Operating Conditions unless otherwise noted. Parameter Transceiver Internal Temperature Transceiver Internal Supply Voltage Transmitter Laser DC Bias Current Transmitted Average Optical Output ...
Page 15
... Addresses 63 and 95 are checksums calculated (per SFF-8472) and stored prior to product shipment. 4. Addresses 68-83 specify the AFCT-701ASDZ ASCII serial number and will vary on a per unit basis. 5. Addresses 84-91 specify the AFCT-701ASDZ ASCII date code and will vary on a per date code basis. 15 ...
Page 16
... Transmitted average optical power (Tx Pwr) is decoded bit unsigned integer in increments of 0.1 μW. 5. Received average optical power (Rx Pwr) is decoded bit unsigned integer in increments of 0.1 μW. 6. Bytes 56-94 are not intended for use with AFCT-701ASDZ, but have been set to default values per SFF-8472. 7. Byte checksum calculated (per SFF-8472) and stored prior to product shipment. ...
Page 17
... Indicates transceiver is powered and real time sense data is ready Ready) Notes: 1. The response time for soft commands of the AFCT-701ASDZ is 100 msec as specified by SFF-8472. 2. Bit 6 is logic OR’d with the SFP TX_DISABLE input on contact 3; either asserted will disable the SFP+ transmitter. Table 15. EEPROM Serial ID Memory Contents – Alarms and Warnings (Address A2h, Bytes 112, 113, 116, 117) ...
Page 18
Figure 6. Module drawing Label format Figure 7. Module label For product information and a complete list of distributors, please go to our website: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies in the United States ...