AFCT-57D5ATPZ Avago Technologies US Inc., AFCT-57D5ATPZ Datasheet - Page 10

• Manufacturer Part Number: AFCT-57D5ATPZ
• Description: SM 8/4/2G SFP, 10Km, RoHS
• Manufacturer: Avago Technologies US Inc.

Specifications of AFCT-57D5ATPZ

• Data Rate: 8.5Gbd
• Wavelength: 1310nm
• Applications: General Purpose
• Voltage - Supply: 2.97 V ~ 3.63 V
• Connector Type: LC Duplex
• Mounting Type: SFP
• Operating Temperature Classification: Commercial
• Package Type: SFP
• Mounting: Snap Fit To Panel
• Pin Count: 20
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Table 7. Transmitter Optical Characteristics
(T
Parameter
Modulated Optical Output Power (OMA)
(Peak-to-Peak)
Average Optical Output Power
Center Wavelength
-20 dB Spectral Width
Side Mode Suppression
Optical Rise/Fall Time (8.5 Gb/s)
RIN
Transmitter Contributed Total Jitter (8.5 Gb/s)
Transmitter Contributed Total Jitter (4.25 Gb/s)
Transmitter Contributed Total Jitter (2.25 Gb/s)
Pout TX_DISABLE Asserted
Notes:
. Max Pout is the lesser of Class  safety limits (CDRH and EN 60825) or receiver power, max.
2. Into single-mode optical fiber.
3. Contributed DJ is measured on an oscilloscope in average mode with 50% threshold and K28.5 pattern. Contributed TJ is the sum of contributed
Table 8. Receiver Optical Characteristics
(T
Parameter
Input Optical Power [Overdrive]
Input Optical Modulation Amplitude
(Peak-to-Peak) 8.5 Gb/s [Sensitivity]
Input Optical Modulation Amplitude
(Peak-to-Peak) 4.25 Gb/s [Sensitivity]
Input Optical Modulation Amplitude
(Peak-to-Peak) 2.25 Gb/s [Sensitivity]
Return Loss
Loss of Signal - Assert
Loss of Signal - De-Assert
Loss of Signal Hysteresis
Notes:
. Maximum input optical power for 8.5Gb/s is +0.5dBm, for 4.25Gb/s is -.0dBm and for 2.25Gb/s is -3.0dBm per ANSI T FC-PI-4.
2. Input Optical Modulation Amplitude (commonly known as sensitivity) requires a valid 8B/0B encoded input.
0
C
C
RJ and contributed DJ. Contributed RJ is calculated for x0
oscilloscope by 4. Per FC-PI-4 (Table 3 - MM jitter output, note ), the actual contributed RJ is allowed to increase above its limit if the actual
contributed DJ decreases below its limits, as long as the component output DJ and TJ remain within their specified FC-PI-4 maximum limits with
the worst case specified component jitter input.
= -10°C to 85°C, VccT, VccR = 3.3 V ±10%)
2
= -10°C to 85°C, VccT, VccR = 3.3V ±10%)
(OMA)
Symbol
P
OMA
OMA
OMA
P
P
P
A
IN
D
D
- P
A
Symbol
Tx,OMA
Pout
l
tr, tf
RIN
TJ
TJ
TJ
P
-2
C
OFF
BER by multiplying the RMS jitter (measured on a single rise or fall edge) from the
Min.
42
29
5
2
-30.0
0.5
Minimum
290
-8.4
260
30
Typ.
Max.
+0.5
-6.0
Typical
Unit
dBm, avg
µW, OMA
µW, OMA
µW, OMA
dB
dBm, OMA
dBm, OMA
dB
Maximum
360
.0
50
-28
0.26
30.9
0.25
59.8
0.25
9.6
-35
Notes
Note 
Note 2
Note 2
Note 2
Unit
µW
dBm
nm
nm
dB
ps
dB/Hz
UI
ps
UI
ps
UI
ps
dBm
Notes
Note , 2
20% - 80%
Note 3
Note 3
Note 3