NL6448BC33-63D NEC, NL6448BC33-63D Datasheet - Page 28

• Manufacturer Part Number: NL6448BC33-63D
• Description: TFT DISPLAY, 10.4"
• Manufacturer: NEC

Specifications of NL6448BC33-63D

• Lcd Display Type: VGA
• Interface Type: LVDS
• Viewing Area (h X W): 158.4mm X 211.2mm
• Supply Voltage: 3.3V
• Operating Temperature Range: -20°C To +70°C
• Pixel Size (h X W): 0.33mm X 0.33mm
• Display Mode: Active
• Backlight Type: CCFL
• Display Technology: LCD
• Luminance: 450cd/m2
• Rohs Compliant: Yes
• Pixel Pitch (h X W): 0.33mm X 0.33mm
• Svhc: No SVHC (20-Jun-2011)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

6.3.2 Environment
6.3.3 Characteristics
⑩ Properly connect the plug (backlight side) to adaptable socket (inverter side) without incomplete
⑪ If the lamp cable is attached on the metal part of the product directly, high frequency leak current
⑫ When handling the product, use of an original protection sheet on the product surface (polarizer) is
⑬ Usually liquid crystals don't leak through the breakage of glasses because of the surface tension of
① Do not operate or store in high temperature, high humidity, dewdrop atmosphere or corrosive gases.
② In order to prevent dew condensation occurring by temperature difference, the product packing
③ Do not operate in high magnetic field. Circuit boards may be broken down by it.
④ This product is not designed as radiation hardened.
The following items are neither defects nor failures.
① Characteristics of the LCD (such as response time, luminance, color uniformity and so on) may be
② Display mura, flicker, vertical seam or small spot may be observed depending on display patterns.
③ Optical characteristics (e.g. luminance, display uniformity, etc.) gradually is going to change
④ Do not display the fixed pattern for a long time because it may cause image sticking. Use a screen
⑤ The display color may be changed depending on viewing angle because of the use of condenser
⑥ Optical characteristics may be changed depending on input signal timings.
⑦ The interference noise between input signal frequency for this product's signal processing board
⑧ After the product is stored under condition of low temperature or dark place for a long time, the cold
connection. After connecting, be careful not to hook the lamp cables because incomplete
connection may occur by hooking the lamp cables. This incomplete connection may cause
abnormal operation of high voltage circuit.
to the metal part may occur, then the brightness may decrease or the lamp may not be turned on.
recommended for protection of product surface. Adhesive type protection sheet may change color
or characteristics of the polarizer.
thin layer and the construction of LCD panel. But, if you contact with liquid crystal for the worst,
please wash it out with soap.
Keep the product in packing box with antistatic pouch in room temperature to avoid dusts and
sunlight, when storing the product.
box should be opened after enough time being left under the environment of an unpacking room.
Evaluate the leaving time sufficiently because a situation of dew condensation occurring is
changed by the environmental temperature and humidity. (Recommended leaving time: 6 hours or
more with packing state)
changed depending on ambient temperature. If the product is stored under condition of low
temperature for a long time, it may cause display mura. In this case, the product should be operated
after enough time being left under condition of operating temperature.
depending on operating time, and especially low temperature, because the LCD has cold cathode
fluorescent lamps.
saver, if the fixed pattern is displayed on the screen.
sheet in the backlight.
and luminance control frequency of the inverter may appear on a display. Set up luminance control
frequency of the inverter so that the interference noise does not appear.
cathode fluorescent lamp may not be turned on under the same condition because of the general
characteristic of cold cathode fluorescent lamp. In addition, when Luminance control ratio is low in
pulse width modulation method inverter, the lamp may not be turned on. In this case, power should
be supplied again.
DATA SHEET DOD-PP-0134 (2nd edition)
NL6448BC33-63D
28