NL3224BC35-20 NEC, NL3224BC35-20 Datasheet - Page 34

• Manufacturer Part Number: NL3224BC35-20
• Description: DISPLAY, LCD GRAPHIC, 320 X 240 DOTS
• Manufacturer: NEC

Specifications of NL3224BC35-20

• Viewing Area (h X W): 83.52mm X 111.36mm
• Supply Voltage: 5V
• Display Mode: Active
• Rohs Compliant: Yes
• Lcd Display Type: TFT
• Interface Type: CMOS
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

6.3.2 Environment
6.3.3 Characteristics
⑨ Do not bend or unbend the lamp cable at the near part of the lamp holding rubber, to avoid the
⑩ Properly connect the plug (backlight side) to adaptable socket (inverter side) without incomplete
⑪ If the lamp cable is attached on the metal part of the product directly, high frequency leak current
⑫ When not connecting shield plate of the LCD module to the customer's equipment ground, inverter
⑬ When handling the product, use of an original protection sheet on the product surface (polarizer) is
⑭ Usually liquid crystals don't leak through the breakage of glasses because of the surface tension of
① Do not operate or store in high temperature, high humidity, dewdrop atmosphere or corrosive gases.
② In order to prevent dew condensation occurring by temperature difference, the product packing box
③ Do not operate in high magnetic field. Circuit boards may be broken down by it.
④ This product is not designed as radiation hardened.
The following items are neither defects nor failures.
① Response time, luminance and color may be changed by ambient temperature.
② Display mura, flicker, vertical seam or small spot may be observed depending on display patterns.
③ Optical characteristics (e.g. luminance, display uniformity, etc.) gradually is going to change
④ Do not display the fixed pattern for a long time because it may cause image sticking. Use a screen
⑤ The display color may be changed depending on viewing angle because of the use of condenser
⑥ Optical characteristics may be changed depending on input signal timings.
⑦ The interference noise between input signal frequency for this product's signal processing board
⑧ After the product is stored under condition of low temperature or dark place for a long time, the
damage for high voltage side of the lamp.
connection. After connecting, be careful not to hook the lamp cables because incomplete
connection may occur by hooking the lamp cables. This incomplete connection may cause
abnormal operation of high voltage circuit.
to the metal part may occur, then the brightness may decrease or the lamp may not be turned on.
noise may create video noise on the LCD screen.
recommended for protection of product surface. Adhesive type protection sheet may change color
or characteristics of the polarizer.
thin layer and the construction of LCD panel. But, if you contact with liquid crystal for the worst,
please wash it out with soap.
Keep the product in packing box with antistatic pouch in room temperature to avoid dusts and
sunlight, when storing the product.
should be opened after enough time being left under the environment of an unpacking room.
Evaluate the leaving time sufficiently because a situation of dew condensation occurring is
changed by the environmental temperature and humidity. (Recommended leaving time: 6 hours or
more with packing state)
depending on operating time, and especially low temperature, because the LCD has cold cathode
fluorescent lamps.
saver, if the fixed pattern is displayed on the screen.
sheet in the backlight.
and luminance control frequency of the inverter may appear on a display. Set up luminance control
frequency of the inverter so that the interference noise does not appear.
cold cathode fluorescent lamp may not be turned on under the same condition because of the
general characteristic of cold cathode fluorescent lamp. In addition, when Luminance control ratio
is low in pulse width modulation method inverter, the lamp may not be turned on. In this case,
power should be supplied again.
DATA SHEET DOD-PP-0297 (15th edition)
NL3224BC35-20
34